Stop position Stod, Product length Prdl | Avery ALS 230 guide

Operators Manual

ALS 230

Stop position ___________________________________________________ STOD

Function: Stop position of the label at the dispensing edge.

Available: Always

Range: 0.0 .... 200.0 mm

Product length ___________________________________________________PRDL

Function: The product length avoids multi labelling in case of difficult products. Normally it is set to AUTO. This means that the product length is set to the label length.

After the product sensor has detected the edge of the product all signals that might be triggered while the product is passing the product sensor are inhibited. This function can be helpful in cases where the product is transparent or has several detection marks or edges. Such a case is shown below.

The product sensor supplies several signals while the product passes the product sensor. If the PRDL is not adjusted according to the dimension of the actual product the warning W_0 may be given of false multiple product detection signals. The defined product length suppresses all signals after the first product sensor signal has been received.

By pressing the keys FUNCTION the parameter PRDL is selected. The data input is selected by pressing the key ENTER.

If an applicator is fitted to the labeller, the product length is not defined as a distance but as the time that the product needs to pass the product sensor. The time is adjustable between 5 and 9999 ms.

Available: Always

Range: AUTO or 5 - 999 mm

Label position_____________________________________________________POS

Function: Position of label on the product.

Only available if no applicator is used.

Range: up to 999.9 mm in steps of 0.1 mm.

Release 11/05

Page 37

Menu structure

Image 39

Avery ALS 230 manual Stop position Stod, Product length Prdl

Contents

Page Page ALS Menu structure Errors and warnings Copyright Important NotesOverview Manufacturer General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Work on the electrical equipment Work on pneumatic equipmentObserve environmental regulations Page Mechanics Description Dispensing mechanics Operator panel Operator panel ALS Electronic Plug board ALS Unpacking of the unit InstallationGeneral setting Preparing the machine Prepare dispensing Insert materialDefine label data Setting Lpit manually Manual adjustment of the Cont parameterCapacitive label sensor Capacitive sensor Label guide Adjust dispense function Stop positionFixed dispensing speed Automatic dispensing speed Apsf Label position on the productProduct data bank Operation Safety recommendation Left hand version Inserting label material 3Initialise new label material Missing label function and web breaks Function Display message Mains switch4Control of dispense unit Dispenser Menu selection Label positionPOS Dispenser active onDispenser stopped OFF Material initialisation Init Label position Stop position Stod Product menu PD0n Start delaySTADDispense speed Velo Blow on time Blow Maintenance Extended standard menu Configuration menuMenu structure Standard menu Extended menu ConfigurationStandard menu Direct Applicator Standard menu Initialisation InitDisplay Function Values Dispensing speed Velo Start delay StadLabel position POS Labelling time Blow Display Function Data value Extended standard menu Label pitch Lpit Label contrastSensor status Sens Product length Prdl Dwell time APT1 Electronic gear ratio adjustment EgraEgra value check Stst Slew speed Slew Restart delay APT3 Blow on time APT2Time constant compensation APT4 Load data bank Load End of air stream signal AstpPrinter dwell time PDT Save parameter in data bank Save Product menu Release 11/05 Menu structure Possible tests ConfigurationPossible adjustments Calling the configuration menu Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Input and sensor check ICH Output check OCHAdditional functions in the standard menu Number of stop bits Sbit Adjustment resettingFACTInterface baud rate Baud Parity bit Pari Label counter Labc Number of data bits DbitRecycle simulates max labels/min Recy Distance sensor to dispensing edge Dist Release 11/05 Configuration Data of the serial interface Serial interface Interface commands Command Description RangeExample Ledg Message in display Bit definition in error flagError number Error message in display Error description Bit definition in warning flag Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Wiring diagram Electronic diagrams Layout dispenser electronic board Jumper position has to be 800 steps Page Message Meaning How to solve Errors and warningsDispenser error messages STO! Power-fail message Into Eeprom Dispenser warnings ALS Technical Specification Technical InformationDescription Details APSF- Sensor Specification Optional function Application specification Labels per minute in relation to different label pitches Performance 375 125 875 625 ALS Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Siehe Machine type Index