English
Rider 11, Rider Rider 11 Bio, Rider 13 Bio, Rider
Workshop manual
Svenska
Workshop manual
Rider 11, Rider Rider 11 Bio, Rider 13 Bio Rider Contents
Troubleshooting chart
General instructions
Safety regulations
Special instructions
IMPORTANT INFORMATION
Special tools
Dimensions
Technical data
Tightening moments
Play
Mowing deck
Technical data
Rear ejector
Side ejector
Technical data
Control points
After first 5 hours
Delivery and dealer service
Pre-delivery service
50 hours service
Dealer service 25 hours service
100 hours service
300 hours service
Maintenance interval in
Maintenance schedule
Maintenance
The engine is switched off The ignition key is removed
To our dealer
Delivery measures
Packaging and unpacking
Parts enclosed in packaging, Rider
Delivery measures
Battery
Measures for contact with acid
Tow plate
Steering wheel
Check the oil level in the engine
Rider 16, 2003 model
Wheels
Checking the oil level in the transmission
IMPORTANT INFORMATION
IMPORTANT INFORMATION
Delivery measures
Test running
Delivery measures
Administration
Speed regulator
General
Design and function
Older engines all versions Newer engines Rider 16
Serial number
Design and function
Side-valve engine Rider 11 and
Engine
Overhead-valve engine Rider 16
Design and function
Design and function
Steering
Design and function
Driving
Mowing deck
Mowing deck with rear ejection, 850 mm
Removing the BioClip plug BioClip 900 mm
Mowing deck with side ejection, 970 mm
BioClip 1030 mm
Mowing height manoeuvring
The attachment’s lifting device
Design and function
22 - English
Removing engine
Reparation instructions
Hold the bolts so that the poles are not put under strain
IMPORTANT INFORMATION
Tie the hose higher than the fuel tank level
Reparation instructions
IMPORTANT INFORMATION
Replacing engine
Reparation instructions
Choke not actuated
Reparation instructions
Reparation instructions
Fuel tank Removal
Fitting
Changing the oil
Checking and adjusting steering wires
Avoid skin contact and wash any spillage with soap and water
Reparation instructions
Reparation instructions
Replacing steering wires
Removal/installation of steering axle
30 - English
Removal/installation of wire wheel
Reparation instructions
A badly adjusted brake can lead to reduced braking capacity
Checking and adjusting brake wire
Rider 13 and Rider
Reparation instructions
Reparation instructions
Checking and adjusting gear control Rider
Checking and adjusting freewheel clutch Rider
Replacing articulated steering bearing
Checking and adjusting throttle control
2 Rider
2 Rider 13 and Rider
Work off the belts from the pulley
Reparation instructions
Replacing bushings
Removal of swing axle
2 Rider 13 and
Reparation instructions
3 Rider
Installation of swing axle
3 Rider 13 and
Reparation instructions
Rider
Removal/installation of gear box
Reparation instructions
Replacing hydrostatic transmission axle sealing collars
Sealing collar replacement - input axle
Reparation instructions
IMPORTANT INFORMATION
Reparation instructions
Sealing collar replacement - outgoing axles
IMPORTANT INFORMATION
IMPORTANT INFORMATION
Reparation instructions
Replacing hydrostatic transmission wire
Removal of hydrostatic transmission wire
4. Remove the transmission cover
Reparation instructions
Reparation instructions
Refitting hydrostatic transmission wire
Reparation instructions
Reparation instructions
Adjustment of transmission neutral position
Bleeding the hydrostatic transmission oil system
Reparation instructions
Transmission maintenance
Oil change
Changing oil - Rider 13 and Rider
Removing the belt
Rider 11, Rider 13 H, Rider 16 H och Rider 14 Pro
Reparation instructions
Checking and adjusting mower deck parallelism
Checking and adjusting mower deck ground pressure
Adjusting Rider 11 and Rider 13 H
Reparation instructions
Adjusting Rider
Adjusting Rider 11 Bio and Rider 13 Bio
Reparation instructions
48 - English
Adjusting cutting height
Adjusting cutting height area
Reparation instructions
IMPORTANT INFORMATION
Reparation instructions
Removing the cutting unit
Reparation instructions
To leave the service position
Dismantling the cutting unit
Wear eye protection and work gloves when working on the mowing deck
Rear and side ejectors
Reparation instructions
Protect your hands by wearing gloves when working with the blades
Belt replacement on BioClip 103 and Combi
Replacing the cutting unit’s belts
Reparation instructions
IMPORTANT INFORMATION
Belt replacement on BioClip
Reparation instructions
Replacing the break-pin BioClip 90, 103 and Combi
When working with the mowing deck, use protective glasses and gloves
Removal of blades with bearings
Reparation instructions
Reparation instructions
The friction washer must be replaced when replacing the shear pin
Press out the axle with a puller
IMPORTANT INFORMATION
Grinding and balancing of blades
When working with the blades, use protective gloves
The friction washer must be replaced when replacing the shear pin
Reparation instructions
Electrical system
Circuit diagram Rider
Electrical system
Circuit diagram Rider 13 and Rider 13 Bio
Electrical system
Circuit diagram Rider
60 - English
7/8/9
Works
Inspecting the safety system
Electrical system
Microswitch Mowing Deck
Microswitch Seat
Microswitch Neutral Position
Main fuse
Ignition and Starter Lock
ENGINE WILL NOT START
Too low or no oil in the engine
ENGINE STARTS BUT DOES NOT RUN SATISFACTORILY
Page
Stop and let the transmission cool down. Clean the cooling fins
Brakes do not work satisfactorily The machine moves while in neutral
Svenska
Svenska
Svenska
´z+H.T¶6w¨
Svenska
114 01
´z+H.T¶6w¨ 2002W51
Also See