English
Rider 11, Rider Rider 11 Bio, Rider 13 Bio, Rider
Workshop manual
Svenska
Workshop manual
Rider 11, Rider Rider 11 Bio, Rider 13 Bio Rider Contents
Troubleshooting chart
Special instructions
Safety regulations
General instructions
IMPORTANT INFORMATION
Special tools
Tightening moments
Technical data
Dimensions
Play
Rear ejector
Technical data
Mowing deck
Side ejector
Control points
Technical data
After first 5 hours
Delivery and dealer service
Pre-delivery service
100 hours service
Dealer service 25 hours service
50 hours service
300 hours service
Maintenance
Maintenance schedule
Maintenance interval in
The engine is switched off The ignition key is removed
Packaging and unpacking
Delivery measures
To our dealer
Parts enclosed in packaging, Rider
Delivery measures
Battery
Measures for contact with acid
Check the oil level in the engine
Steering wheel
Tow plate
Rider 16, 2003 model
IMPORTANT INFORMATION
Checking the oil level in the transmission
Wheels
IMPORTANT INFORMATION
Test running
Delivery measures
Delivery measures
Administration
Speed regulator
Design and function
General
Older engines all versions Newer engines Rider 16
Serial number
Design and function
Overhead-valve engine Rider 16
Engine
Side-valve engine Rider 11 and
Design and function
Steering
Design and function
Design and function
Driving
Mowing deck
Mowing deck with side ejection, 970 mm
Removing the BioClip plug BioClip 900 mm
Mowing deck with rear ejection, 850 mm
BioClip 1030 mm
Design and function
The attachment’s lifting device
Mowing height manoeuvring
22 - English
Hold the bolts so that the poles are not put under strain
Reparation instructions
Removing engine
IMPORTANT INFORMATION
Reparation instructions
Tie the hose higher than the fuel tank level
IMPORTANT INFORMATION
Replacing engine
Reparation instructions
Reparation instructions
Choke not actuated
Reparation instructions
Fuel tank Removal
Fitting
Avoid skin contact and wash any spillage with soap and water
Checking and adjusting steering wires
Changing the oil
Reparation instructions
Reparation instructions
Replacing steering wires
Removal/installation of steering axle
30 - English
Removal/installation of wire wheel
Reparation instructions
Rider 13 and Rider
Checking and adjusting brake wire
A badly adjusted brake can lead to reduced braking capacity
Reparation instructions
Reparation instructions
Checking and adjusting gear control Rider
Checking and adjusting freewheel clutch Rider
2 Rider
Checking and adjusting throttle control
Replacing articulated steering bearing
2 Rider 13 and Rider
Reparation instructions
Work off the belts from the pulley
2 Rider 13 and
Removal of swing axle
Replacing bushings
Reparation instructions
3 Rider 13 and
Installation of swing axle
3 Rider
Reparation instructions
Rider
Removal/installation of gear box
Reparation instructions
Reparation instructions
Sealing collar replacement - input axle
Replacing hydrostatic transmission axle sealing collars
IMPORTANT INFORMATION
IMPORTANT INFORMATION
Sealing collar replacement - outgoing axles
Reparation instructions
IMPORTANT INFORMATION
Reparation instructions
Replacing hydrostatic transmission wire
Removal of hydrostatic transmission wire
Reparation instructions
4. Remove the transmission cover
Refitting hydrostatic transmission wire
Reparation instructions
Reparation instructions
Reparation instructions
Adjustment of transmission neutral position
Bleeding the hydrostatic transmission oil system
Reparation instructions
Transmission maintenance
Oil change
Rider 11, Rider 13 H, Rider 16 H och Rider 14 Pro
Removing the belt
Changing oil - Rider 13 and Rider
Reparation instructions
Adjusting Rider 11 and Rider 13 H
Checking and adjusting mower deck ground pressure
Checking and adjusting mower deck parallelism
Reparation instructions
Reparation instructions
Adjusting Rider 11 Bio and Rider 13 Bio
Adjusting Rider
48 - English
Reparation instructions
Adjusting cutting height area
Adjusting cutting height
IMPORTANT INFORMATION
Removing the cutting unit
Reparation instructions
To leave the service position
Reparation instructions
Rear and side ejectors
Wear eye protection and work gloves when working on the mowing deck
Dismantling the cutting unit
Reparation instructions
Replacing the cutting unit’s belts
Belt replacement on BioClip 103 and Combi
Protect your hands by wearing gloves when working with the blades
Reparation instructions
IMPORTANT INFORMATION
Belt replacement on BioClip
Reparation instructions
Removal of blades with bearings
When working with the mowing deck, use protective glasses and gloves
Replacing the break-pin BioClip 90, 103 and Combi
Reparation instructions
Press out the axle with a puller
The friction washer must be replaced when replacing the shear pin
Reparation instructions
IMPORTANT INFORMATION
The friction washer must be replaced when replacing the shear pin
When working with the blades, use protective gloves
Grinding and balancing of blades
Reparation instructions
Circuit diagram Rider
Electrical system
Circuit diagram Rider 13 and Rider 13 Bio
Electrical system
60 - English
Circuit diagram Rider
Electrical system
7/8/9
Works
Inspecting the safety system
Electrical system
Microswitch Mowing Deck
Microswitch Seat
Microswitch Neutral Position
Ignition and Starter Lock
Main fuse
ENGINE WILL NOT START
ENGINE STARTS BUT DOES NOT RUN SATISFACTORILY
Too low or no oil in the engine
Page
Stop and let the transmission cool down. Clean the cooling fins
Brakes do not work satisfactorily The machine moves while in neutral
Svenska
Svenska
Svenska
´z+H.T¶6w¨
Svenska
´z+H.T¶6w¨ 2002W51
114 01
Also See