Brother rh-918a manual Replacement parts list for specification changes, specifications

2. SPECIFICATIONS

2-5. Replacement parts list for specification changes

The sewing machine can be changed to any one of L1 - L7 for -02 and -52 specifications by replacing the specified parts with the appropriate parts given below.

-02 specifications

Specifications	Replacement parts set
(buttonhole length)
L1	S44238-001
(14 - 18 mm)
L2	S44239-001
(18 - 22 mm)
L3	S44240-001
(22 - 26 mm)
L4	S44271-001
(26 - 30 mm)
L5	S44272-001
(28 - 32 mm)
L6	S44273-001
(32 - 36 mm)
L7	S44274-001
(36 - 40 mm)

Plate R assembly	Hammer	Specification harness
Plate L assembly
S38576-301	S37702-001 (S12)	S43337-000
S38577-201	S37704-001 (S16)
S38578-301	S37704-001 (S16)	S43338-000
S38579-201	S37706-001 (S20)
S38580-301	S37706-001 (S20)	S43339-000
S38581-201	S37708-001 (S24)
S38582-301	S37708-001 (S24)	S43340-000
S38583-201	S42053-001 (S28)
S41470-101	S37197-001 (26)	S43341-000
S41471-101	S37199-001 (30)
S41472-101	S37199-001 (30)	S43342-000
S41473-101	S37201-001 (34)
S41474-101	S37201-001 (34)	S43343-000
S41475-101	S35093-001 (38)

0797Q 0799Q

Note: There is 10 mm of difference in the knife cutting position between L1 - L4 and L5 - L7 specifications. (Refer to page 63.)

-52 specifications

Specifications	Plate R assembly	Hammer	Specification harness	Cloth feed plate R
(buttonhole length)	Plate L assembly
L1	S38576-301	S37702-001 (S12)	S43360-000	S43809-001
(14 - 18 mm)	S38577-201	S37704-001 (S16)
L2	S38578-301	S37704-001 (S16)	S43361-000	S43809-001
(18 - 22 mm)	S38579-201	S37706-001 (S20)
L3	S38580-301	S37706-001 (S20)	S43362-000	S42139-101
(22 - 26 mm)	S38581-201	S37708-001 (S24)
L4	S38582-301	S37708-001 (S24)	S43363-000	S42139-101
(26 - 30 mm)	S38583-201	S42053-001 (S28)
L5	S41470-101	S37197-001 (26)	S43364-000	S43809-001
(28 - 32 mm)	S41471-101	S37199-001 (30)
L6	S41472-101	S37199-001 (30)	S43365-000	S42139-101
(32 - 36 mm)	S41473-101	S37201-001 (34)
L7	S41474-101	S37201-001 (34)	S43366-000	S42139-101
(36 - 40 mm)	S41475-101	S35093-001 (38)

Note: There is 10 mm of difference in the knife cutting position between L1 - L4 and L5 - L7 specifications. (Refer to page 63.)

RH-981A

4