No. | Initial value | Setting range |
| Setting details |
| |
|
|
| Overtime function |
|
| |
16 | 3 (minutes) | 0 - 30 (minutes) | 0: None |
|
| |
|
|
| ||||
|
|
| and [Err 190] is displayed. |
| ||
|
|
| Correction stitch function (correction stitch icon [when off/when on] | |||
|
|
| operation) |
|
| |
17 | 1 | 0 - 3 | 0: Half stitch correction sewing / Single stitch correction sewing |
| ||
1: No correction sewing / Single stitch correction sewing |
| |||||
|
|
|
| |||
|
|
| 2: Reverse correction sewing (reverse feed) / Single stitch correction sewing | |||
|
|
| 3: Forced single stitch sewing after thread trimming / Single stitch sewing | |||
|
|
| Thread wiping and presser foot lifting timing after thread is trimmed and | |||
18 | 50 (ms) | 10 - 200 (ms) | sewing stops |
| 2245M | |
Motor |
| |||||
|
|
|
|
| ||
|
|
|
|
|
| |
19 | 50 (ms) | 10- 200 (ms) |
|
|
| |
|
|
| Thread wiping |
|
| |
20 | 50 (ms) | 10 - 200 (ms) |
|
| ||
Presser |
|
| ||||
|
|
|
|
| ||
|
|
| foot lifting | Needle up | (Fully ON) | |
|
|
|
| |||
|
|
|
|
| ||
21 | 0 | 0 - 1 | Start backtacking operation |
| ||
0: Stitch Nos. A, B (N backtacks) |
| |||||
|
|
| 1: Stitch Nos. A, B, A, B (N backtacks doubled) |
| ||
22 | 0 | 0 - 1 | End backtacking operation |
| ||
0: Stitch Nos. C, D |
|
| ||||
|
|
| 1: Stitch Nos. C, D, C, D (N backtacks doubled) |
| ||
|
|
| Speed when changing to end backtacking |
| ||
26 | 0 | 0 - 1 | 0: Speed decelerates to low speed, then end backtacking starts | |||
1: Speed decelerates to end backtacking speed, then end backtacking starts | ||||||
|
|
| ||||
|
|
| (allows shortening of cycle time) |
| ||
27 | 0 | 0 - 1 | Continuous backtacking operation |
| ||
0: Stitch Nos. A, B, C, D |
| |||||
|
|
| 1: Stitch Nos. A, B x D times |
| ||
|
|
| Feed direction when sewing is stopped immediately after start backtacking is | |||
|
|
| complete |
|
| |
|
|
| 0: Quick reverse solenoid turns off and feed returns |
| ||
|
|
| to normal direction, then stops |
| ||
28 | 0 | 0 - 1 | 1: After sewing stops, the quick reverse solenoid |
| ||
|
|
|
| |||
|
|
| turns off (if No. 31 is set to “0”, sewing starts again |
| ||
|
|
| when the treadle is depressed slghtly |
| ||
|
|
|
|
| 2246M | |
|
|
|
| |||
30 | 150 (ms) | 0 - 500 (ms) | Delay time for motor to start when presser foot is lifted and sewing machine | |||
starts operating when automatic presser foot lifting is being used | ||||||
|
|
| ||||
5 |