LED and Beeper Indications
LED and Beeper Indications
INDICATION | DESCRIPTION | LED | BEEPER | |
|
|
|
| |
|
|
|
| |
| The reader is in the process of pow- |
| Reader beeps four times at highest | |
| frequency and volume upon power- | |||
| ||||
|
| up. | ||
|
|
| ||
|
|
|
| |
|
| LED behavior for this indica- | The reader will beep once at current | |
Good Read Beep | A label has been successfully | tion is configurable via the | frequency, volume, | |
scanned by the reader. | feature “Good Read: When | setting and duration upon a suc- | ||
| ||||
|
| to Indicate” | cessful label scan. | |
|
|
|
| |
ROM Failure | There is an error in the reader's soft- | Flashes | Reader sounds one error beep at | |
ware/programming | highest volume. | |||
|
| |||
|
|
|
| |
Limited Scanning | Indicates that a host connection is |
| Reader 'chirps' six times at the high- | |
not established when the IBM or | N/A | |||
Label Read | est frequency and current volume. | |||
USB interface is enabled. |
| |||
|
|
| ||
|
|
|
| |
Reader Active | The reader is active and ready to | The LED is lit steadilya | N/A | |
Mode | scan. | |||
|
| |||
|
|
|
| |
Reader | The reader has been disabled by the | The LED blinks continuously | N/A | |
Disabled | host. | |||
|
| |||
|
|
|
| |
Green Spot is on | While in Stand Mode or Trigger |
|
| |
Stand Mode the green spot shall be | N/A | N/A | ||
continuously | ||||
on while in stand watch state. |
|
| ||
|
|
| ||
|
|
|
| |
| Upon successful read of a label, the |
|
| |
Green Spota flashes | software shall turn the green spot | N/A | N/A | |
momentarily | on for the time specified by the con- | |||
|
| |||
| figured value. |
|
| |
|
|
|
| |
Programming Mode - The following indications ONLY occur when the reader is in Programming Mode. | ||||
|
|
|
| |
Label Program- | A valid programming label has been | LED blinks continuously | Reader sounds four low frequency | |
ming Mode Entry | scanned. | beeps. | ||
| ||||
|
|
|
| |
Label Program- |
|
| Reader sounds three times at low- | |
ming Mode Rejec- | A label has been rejected. | N/A | ||
est frequency & current volume. | ||||
tion of Label |
|
| ||
|
|
| ||
|
|
|
| |
Label Program- | In cases where multiple labels must |
| Reader sounds one short beep at | |
ming Mode Accep- | be scanned to program one feature, |
| ||
N/A | highest frequency & current vol- | |||
tance of Partial | this indication acknowledges each | |||
| ume. | |||
Label | portion as it is successfully scanned. |
| ||
|
| |||
|
|
|
| |
Label Program- | Configuration option(s) have been |
| Reader sounds one high frequency | |
ming Mode Accep- | successfully programmed via labels |
| ||
N/A | beep and 4 low frequency beeps | |||
tance of | and the reader has exited Program- | |||
| followed by reset beeps. | |||
Programming | ming Mode. |
| ||
|
| |||
|
|
|
| |
Label Program- |
|
| Reader sounds two times at low fre- | |
ming Mode Cancel | Cancel label has been scanned. | N/A | ||
quency and current volume. | ||||
Item Entry |
|
| ||
|
|
| ||
|
|
|
| |
a. Except when in sleep mode or when a Good Read LED Duration other than 00 is selected | ||||
286 | Gryphon™ I GD4100 |
