Appendix C Miscellaneous Clock Info, Fig. C.2 | dbx Pro QUANTUM

Appendix C Miscellaneous Clock Info

QUANTUM

C.2 QUANTUM Sync Input (cont.)

not allow the user to change the termination setting. These pieces of equipment are usually provided with a permanent termination. If you use QUANTUM with another piece of terminated equipment in a tapped configuration, you should unterminate QUANTUM’s sync input. The same is true if you wish to use several QUANTUMs in a tapped configuration. QUANTUM can also be used in a daisy chain fashion. In a daisy chain configuration, each piece of equipment can remain terminated (and should if you are using a SuperClock) and so the termination can remain in the default position.

Whatever configuration you choose, always use high-quality 75 ohm coaxial cable for your sync connections. In addi- tion, keep the cable runs as short as possible. The preceding is especially true when using SuperClock because the fre- quencies are much higher. Failure to follow these guidelines could cause decreased audio performance and/or syn- chronization problems.

Daisy Chain Configuration

Sync Source

A

Quantum

C

Tapped Configuration

Sync Source

A

Quantum

C

Fig. C.2

®

70	QUANTUM User Manual

Image 80

dbx Pro QUANTUM user manual Appendix C Miscellaneous Clock Info, Fig. C.2

Contents

Quantum Important Safety Instructions Declaration Conformity Table of Contents Quantum Figure Index Page Intro What is QUANTUM? Introduction Warranty Introduction What is QUANTUM?Service Contact Info Quantum Section Front Panel Getting StartedRear Panel Connections Getting Started Section Front Panel Signal Path Quantum Wizard Quantum is a Mastering Processor that has many features Getting Started Section Mastering and the Quantum Quantum Navigation Navigation Multiband Compressor Navigating the Broadband Compressor Navigation Section Broadband Compressor Navigating the Multiband Gate Multiband Gate Navigating the Broadband Gate Navigation Section Broadband Gate Navigating the Multiband Limiter Multiband Limiter Navigating theBroadband Limiter Navigation Section Broadband Limiter Navigating the Multiband EQ/XOver EQ/XOver Navigating the Broadband EQ/SEQ Navigation Section EQ/SEQ Navigating Norm/Output Norm/Output Navigating Other Navigation Section Other Navigating Utility Utility Section Software Operations FX Chains Software Operations Section FX Chains Chain Type Stereo Broadband Chain Type Mono Mono Input CH1 or CH2 Software Operations Section Programs/Setups Program Pop Master Saving a Setup Section Software Operations Section Saving a Setup Saving a ProgramReplace Old Store New Bypass Function MetersAnalog Meters TSE Level Meters Software Operations Section Meters Digital MetersMeter Options Compressor Monitor Outputs LimiterGate / Expander De-Esser Detailed Detailed Parameters Multiband Compression Detailed Parameters Section Multiband Compression Broadband Compression Detailed Parameters Section Broadband Compression Ratio 11.0 to 115 per band or global Attack 0.1 to 200 m Sec per band or globalRelease 360 to 5 dB / Sec per band or global Max ATT 0 to Inf. dB per band or global Detailed Parameters Section Broadband Gate Multiband Limiting Broadband Limiting Attack .01 to 200 m Sec per band or globalLimiter On/Off Type PkStop+/RMS Detailed Parameters Section Broadband Limiting EQ On/OffPOS Pre/Post Type Const Q / Adapt Q XOver Detailed Parameters Section SEQ Schain EQ On/OffSEQ1 FC 20.0 Hz to 20.0 kHz SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHz Stereo Adjust Type De-Esser Detailed Parameters Section Ambience13 TCM Normalization Output Dither Out All or Digital Detailed Parameters Section OutputShaping S1 or S2 Page Utilities Utilities Input Output Midi CC Map Utilities Section OutputDigital Input Controls Setup Sysex Data Midi ChannelsMidi Program Changes Sysex Dump Misc Utilities Section Setup Sysex DataA/D Calibrate Page Guide Application Guide Analog MasteringHardware Software Application Guide Section Digital Mastering DAW to DAT Application Guide Section Analog Tracking 586 Digital Tracking Application Guide Section Analog Mixing Digital Mixing Application Guide Section Analog to Digital Converter Sample Rate Converter QUANTUMAppendix Hard & Soft Resets Change Default Startup ProgramAppendix a Miscellaneous Information Front Panel Lockout By Roger Johnson TypeIV White Paper Appendix B Appendix B TypeIV White Paper Converted Level vs. Input Level Type Amplitude Time Clip Level High-Frequency Information Completely Lost Appendix C Midi Clock Info Clock Modes Quantum Sync Input Fig. C.1 Appendix C Miscellaneous Clock Info Fig. C.2 Procedures Request One Setup 02hReceive One Setup 43h Sysex Definitions Appendix D Appendix D Sysex Definitions Reset Device 21h Sysex Setup Dump SampleProcedure Setup Dump Version Setup Type and Setup Number Appendix E Midi CC Tables Midi CC MultiBand Chains Midi CC Tables Appendix E Midi CC MultiBand Chains Midi CC Stereo Non-MultiBand Midi CC Dual Mono Chains Midi CC Stereo Non-Multiband Midi CC Tables Appendix E Midi CC Dual Mono Chains Appendix F Factory Presets Factory Programs Mono Factory SetupsStereo Appendix G Specifications Specifications Appendix H Appendix H Quantum Harman International Company