dbx Pro QUANTUM Appendix D

®

Appendix D

QUANTUM

71

Hex Value Definition

F0(h) System Exclusive 'Begin Message' byte

00(h)

01(h) Manufacturer's ID Number (dbx)

1E(h)

0n(h)

n = units Device or SYSEX Channel number (minus one) e.g. 01(h) is device or SYSEX Ch 1...01(h) is device or SYSEX

Ch 2, etc...0F(h) is device or SYSEX Ch 16

dd

dd = device ID number 01(h) identifies the QUANTUM

pp

pp = Procedure number. The different procedure's names and general formats are described

in the Procedures Section.

dd(1)1, dd(1)2......dd(n)1, dd(n)2

dd = Data as needed by procedures. Since the standard MMA MIDI Specification reserves 80(h) through FF(h) (decimal

numbers 128 through 255) for specific commands, a split byte format is adopted for all data communication in this SYSEX

implementation. dd(n)2 denotes the 1st through 7th bits of the nth byte and dd(n)1 denotes th 8th bit of the nth byte.

Note: All data that is requested or received, is in split byte format unless noted otherwise.

F7(h) System Exclusive 'End Message' byte

Procedures

In the following section, SYS_HEAD refers to a valid System Exclusive header. The System Exclusive header starts with

the System Exclusive status byte, and includes all bytes through the dbx device type. F7(h) is the System Exclusive

'Message End' byte. All SYSEX numbers in the format definition of each procedure are given as hexadecimal values,

along with this symbol (h) for clarification. Binary numbers are identified with this symbol (b).

Request One Setup (02h)

SYS_HEAD, 02(h), yy(1)1, yy(1)2, yy(2)1, yy(2)2, zz1, zz2 F7(h)

When yy = Setup Number: 1-100 (0-63h)

When zz = 6Ch Linked Setup type is selected

When zz = 6Dh Dual Mono Setup type is selected

When a Request One Setup procedure is received, the QUANTUM will respond with a Receive One Setup proce-

dure.

Receive One Setup (43h)

SYS_HEAD 43(h), vv(1)1, vv(1)2, vv(2)1, vv(2)2, xx1, xx2, yy1, yy2, zz(1)1, zz(1)2, zz(2)1, zz(2)2, dd(1st)1,dd(1st)2,

dd(nth)1, dd(nth)2, F7(h)

vv .software version number

When xx = 00(h) Dual Mono is selected

When xx = 01(h) Linked Type is selected

QUANTUM User Manual

SYSEX Definitions

Contents

Main IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING: SAFETY INSTRUCTIONS Normal Alt BLACK IMPORTANT SAFETY INSTRUCTIONS ELECTROMAGNETIC COMPATIBILITY DECLARATION OF CONFORMITY Introduction Section 1 - Getting Started Section 2 - Navigation Section 3 - Software Operations Section 4 - Detailed Parameters Figure Index Page Page INTRODUCTION Introduction 1.2 Service Contact Info iii 1.3 Warranty 1.1 What is QUANTUM? (cont.) Page Page 2 1.1 Rear Panel Connections 1.2 Front Panel 1.2 Front Panel (cont.) Analog Level Meters TSE Audio Level Meters LCD Display Data Wheel / Selector 4 1.2 Front Panel (cont.) 1.3 QUANTUM Wizard 1.4 Signal Path Getting Started Section 1 5 The Quantum is a Mastering Processor that has many features: 1.5 Mastering and the Quantum 6 1.5 Mastering and the Quantum (cont.) Page 8 4 All Bands 1 Navigating the"Multiband Compressor" NAVIGATION 2.1 Multiband Compressor 9 2.2 Broadband Compressor Navigating the "Broadband Compressor" 10 2.3 Multiband Gate Navigating the "Multiband Gate" 11 2.4 Broadband Gate Navigating the "Broadband Gate" 12 2.5 Multiband Limiter Navigating the "Multiband Limiter" Navigating the"Broadband Limiter" 14 2.7 EQ/XOver EQ XOver Navigating the "Multiband EQ/XOver" 15 2.8 EQ/SEQ The "EQ/SEQ" button toggles between EQ and SEQ. Depress once to access EQ and a second time for SEQ EQ SEQ Navigating the "Broadband EQ/SEQ" SChain On/Off Type 16 2.9 Norm/Output Normalize Output Navigating "Norm/Output" 17 2.10 Other Navigating "Other" 18 2.11 Utility Navigating "Utility" Page 20 Fig.3.1 3.1 FX Chains Dynamics SOFTWARE OPERATIONS 21 3.1 FX Chains (cont.) Fig 3.2 Chain Type: Stereo Broadband Dynamics 22 3.1 FX Chains (cont.) Chain Type: Mono Dynamics 23 3.2 Programs/Setups Program: 1 "Pop Master 1" Stereo Setup Library 24 3.3 Saving a Setup Program 3: "Pop Master 1" Mono Setup Library 3.2 Programs/Setups (cont.) 25 Replace Old: 3.4 Saving a Program Store New: Saving a program 26 BYPASS 3.6 Meters Analog Meters TSE Analog Meters 27 Digital Meters Meter Options Compressor Gain Reduction Meter Input/Output Curve 28 Limiter 3.7 Monitor Outputs Gate / Expander De-Esser Page 30 4.1 Multiband Compression Compressor LOC/On/Off Band 1 to 4 On/Off OverEasy 1-10 (per band or global) 31 4.1 Multiband Compression (cont.) Threshold -60 to 0 dB (per band or global) Ratio 0.75 to Inf:1 (per band or global) Gain -20 to +20 dB (per band or global) 32 4.2 Broadband Compression Compressor On/Off OverEasy 1-10 Auto On/Off 33 4.2 Broadband Compression (cont.) Gain -20 to +20 dB 4.3 Multiband Gate Attack 0.1 m Sec to 200 m Sec 34 4.3 Multiband Gate (cont.) 4.4 Broadband Gate 35 4.4 Broadband Gate (cont.) 4.5 Multiband Limiting 36 4.5 Multiband Limiting (cont.) Attack .01 to 200 m Sec (per band or global) 4.6 Broadband Limiting Release 360 to 5 dB / Sec (per band or global) 37 4.6 Broadband Limiting (cont.) Release 360 to 5 dB / Sec (per band or global) 4.7 EQ EQ On/Off 38 4.7 EQ (cont.) 4.8 XOver 39 4.9 SEQ 40 4.9 SEQ (cont.) 4.10 Type IV 4.11 Stereo Adjust 41 4.12 Ambience 4.13 TCM 4.14 De-Esser 42 4.14 De-Esser (cont.) Amount 0 to 100% 4.15 Normalization 4.16 Output Page Page Page Utilities 46 Section 5 QUANTUM UTILITIES 5.1 Input 5.2 Output CONNECTIONS 47 5.2 Output (cont.) SCMS 5.3 Digital Input Controls 5.4 MIDI CC Map Section 5 QUANTUM 5.6 MIDI Program Changes 5.7 SYSEX Dump 5.8 Setup SYSEX Data MIDI CH Page Page Page 52 6.1 Analog Mastering 53 6.2 Digital Mastering 54 6.3 DAW to DAT 55 6.4 Analog T racking CHANNEL TWO CHANNEL ONE 2. Change the CLOCK to INT96. 56 CHANNEL TWO CHANNEL ONE 2. Change the CLOCK to desired sample rate. 4. Set the Bits to match the digital recorders input format. 57 6.6 Analog Mixing 58 6.7 Digital Mixing 59 6.8 Analog to Digital Converter CHANNEL TWO CHANNEL ONE 2. Change the CLOCK to desired internal sample rate. 60 6.9 Sample Rate Converter Page Appendix A QUANTUM QUANTUM dbx Type IV Conversion System White Paper by Roger Johnson Page Page Appendix B QUANTUM Figure 3a - Signal Having Low and High Frequency Content Amplitude Time Amplitude } 68 MIDI Clock Info Appendix C QUANTUM C.1 Clock Modes Possible Clock Modes 1.Analog In 2.Digital in - AES Appendix C Miscellaneous Clock Info 69 C.2 QUANTUM Sync Input 70 Appendix C QUANTUM Sync Source A Quantum C Sync Source A Quantum C C.2 QUANTUM Sync Input (cont.) Daisy Chain Configuration Appendix D Hex Value Definition Procedures Request One Setup (02h) Receive One Setup (43h) Appendix D QUANTUM Request Bulk Dump (49h) Receive Bulk Dump (48h) Receive Key Scan Code (54h) Receive Key Accepted (56h) Appendix D 74 Appendix E QUANTUM 74 E.1 MIDI CC - MultiBand Chains Appendix E 75 E.1 MIDI CC - MultiBand Chains (cont.) E.2 MIDI CC - Stereo Non-MultiBand 76 Appendix E QUANTUM E.2 MIDI CC - Stereo Non-Multiband (cont.) E.3 MIDI CC - Dual Mono Chains Appendix E 77 E.3 MIDI CC - Dual Mono Chains (cont.) 78 Appendix F QUANTUM Factory Presets F.1 Factory Programs Appendix F 79 Stereo: Mono: F-2 Factory Setups Appendix G QUANTUM Specifications