
Pr.
Explanation
Settings
Factory Setting
NOTE
11.00 | 0: No function | 0 |
| |
Output Terminal | 1: AC drive operational |
| ||
| MO2/RA2 | 2: Master frequency attained |
|
|
| 3: Zero speed |
|
| |
11.01 | Output Terminal | 4: Over torque detection | 0 |
|
| MO3/RA3 | 5: |
|
|
|
| 6: |
|
|
|
|
|
| |
|
| 7: Operation mode indication |
|
|
| 8: Fault indication |
|
| |
11.02 | Output Terminal | 9: Desired frequency 1 attained | 0 |
|
| MO4/RA4 | 10: Terminal count value attained |
|
|
|
| 11: Preliminary count value attained |
|
|
|
| 12: Over Voltage Stall supervision |
|
|
| 13: Over Current Stall supervision |
|
| |
11.03 | Output Terminal | 14: Heat sink overheat warning | 0 |
|
| MO5/RA5 | 15: Over Voltage supervision |
|
|
| 16: PID supervision |
|
| |
11.04 | Output Terminal | 17: Forward command | 0 |
|
| MO6/RA6 | 18: Reverse command |
|
|
|
| 19: Zero speed output signal |
|
|
| 20: Warning(FbE,Cexx, AoL2, AUE, SAvE) |
|
| |
| 21: Brake control (Desired frequency | 0 |
| |
11.05 | Output Terminal |
| ||
attained) |
| |||
| MO7/RA7 |
|
| |
| 22: Drive ready |
|
| |
|
|
|
| |
|
| 23: Desired frequency 2 attained |
|
|
| 0: No function | 0 |
| |
11.06 | 1: |
|
| |
Terminal (MI7) | 2: |
|
| |
|
|
| ||
|
| 3: |
|
|
| 4: | 0 |
| |
11.07 | 5: External reset |
|
| |
Terminal (MI8) | 6: Accel/Decel inhibit |
|
| |
|
|
| ||
|
| 7: Accel/Decel time selection command |
|
|
|
| 8: Jog Operation |
|
|
|
| 0 |
| |
| 9: External base block |
| ||
11.08 |
|
| ||
Terminal (MI9) | 10: Up: Increment master frequency |
|
| |
|
|
| ||
|
| 11: Down: Decrement master frequency |
|
|
|
| 12: Counter Trigger Signal |
|
|
|
| 0 |
| |
| 13: Counter reset |
| ||
11.09 |
|
| ||
14: E.F. External Fault Input |
|
| ||
Terminal (MI10) |
|
| ||
| 15: PID function disabled |
|
| |
|
|
|
| |
|
| 16: Output shutoff stop |
|
|
|
| 0 |
| |
|
| 17: Parameter lock enable |
| |
11.10 | 18: Operation command selection (external |
|
| |
Terminal (MI11) | terminals) |
|
| |
|
|
| ||
|
| 19: Operation command selection (keypad) |
|
|
|
| 20: Operation command selection |
|
|
11.11 | (communication) | 0 |
| |
| Terminal (MI12) | 21: FWD/REV command |
|
|
|
| 22: Source of second frequency command |
|
|
|
| 23: Run/Stop PLC Program (PLC1) (NOT |
|
|
|
| for VFD*E*C models) |
|
|
English- 28