Delta Electronics VFD-XXXE quick start General Specifications

Control Characteristics

Operating Characteristics

Enviromental Conditions

General Specifications

Control System		SPWM(Sinusoidal Pulse Width Modulation) control (V/f or sensorless vector
		control)
Frequency Setting Resolution		0.01Hz
Output Frequency Resolution		0.01Hz
Torque Characteristics		Including the auto-torque/auto-slip compensation; starting torque can be 150%
		at 3.0Hz
Overload Endurance		150% of rated current for 1 minute
Skip Frequency		Three zones, setting range 0.1-600Hz
Accel/Decel Time		0.1 to 600 seconds (2 Independent settings for Accel/Decel time)
Stall Prevention Level		Setting 20 to 250% of rated current
DC Brake		Operation frequency 0.1-600.0Hz, output 0-100% rated current
		Start time 0-60 seconds, stop time 0-60 seconds
Regenerated Brake Torque		Approx. 20% (up to 125% possible with optional brake resistor or externally
		mounted brake unit, 1-15hp (0.75-11kW) models have brake chopper built-in)
V/f Pattern		4-point adjustable V/f pattern
Frequency	Keypad	Setting by
		Potentiometer-5kΩ/0.5W, 0 to +10VDC, 4 to 20mA, RS-485 interface; Multi-
Setting	External Signal
		function Inputs 3 to 9 (15 steps, Jog, up/down)
Operation	Keypad	Set by RUNand STOP
Setting	External Signal	2 wires/3 wires ((MI1, MI2, MI3)), JOG operation, RS-485 serial interface
Signal		(MODBUS), programmable logic controller
Multi-function Input Signal		Multi-step selection 0 to 15, Jog, accel/decel inhibit, 2 accel/decel switches,
		counter, , external Base Block, ACI/AVI selections, driver reset, UP/DOWN key
		settings, NPN/PNP input selection
Multi-function Output		AC drive operating, frequency attained, zero speed, Base Block, fault indication,
Indication		overheat alarm, emergency stop and status selections of input terminals
Analog Output Signal		Output frequency/current
Alarm Output Contact		Contact will be On when drive malfunctions (1 Form C/change-over contact and
		1 open collector output) for standard type)
		Built-in PLC(NOT for CANopen models), AVR, accel/decel S-Curve, over-
		voltage/over-current stall prevention, 5 fault records, reverse inhibition,
		momentary power loss restart, DC brake, auto torque/slip compensation, auto
		tuning, adjustable carrier frequency, output frequency limits, parameter
Operation Functions		lock/reset, vector control, PID control, external counter, MODBUS
		communication, abnormal reset, abnormal re-start, power-saving, fan control,
		sleep/wake frequency, 1st/2nd frequency source selections, 1st/2nd frequency
		source combination, NPN/PNP selection, parameters for motor 0 to motor 3,
		DEB and OOB (Out Of Balance Detection)(for washing machine)
Protection Functions		Over voltage, over current, under voltage, external fault, overload, ground fault,
		overheating, electronic thermal, IGBT short circuit, PTC
		6-key, 7-segment LED with 4-digit, 5 status LEDs, master frequency, output
Display Keypad (optional)		frequency, output current, custom units, parameter values for setup and lock,
		faults, RUN, STOP, RESET, FWD/REV, PLC
		VFD002E11T/21T/23T, VFD004E11T/21T/23T/43T,
		VFD007E21T/23T/43T, VFD015E23T/43T, VFD007E11A, VFD015E21A,
Built-in Brake Chopper		VFD022E21A/23A/43A, VFD037E23A/43A VFD007E11C, VFD015E21C,
		VFD022E21C/23C/43C, VFD037E23C/43C, VFD055E23A/43A,
		VFD075E23A/43A, VFD110E43A, VFD055E23C/43C, VFD075E23C/43C,
		VFD110E43C
Built-in EMI Filter		For 230V 1-phase and 460V 3-phase models.
Enclosure Rating		IP20
Pollution Degree		2
Installation Location		Altitude 1,000 m or lower, keep from corrosive gasses, liquid and dust
Ambient Temperature		-10oC to 50oC (40oC for side-by-side mounting) Non-Condensing and not frozen

English- 3