Speaker Layout

The illustration below shows a basic example of installation of the amplifier combined with 8 speakers and a monitor.

Subwoofer

Center speaker

Surround back speakers

Front speakers

Place the front speakers to theSurround speakers sides of the monitor or screen and

as flush with the screen surface as possible.

Two surround back speakers are required to use the THX Ultra2 Cinema,THX Music mode and THX Games mode.

Set the surround back speakers so that the distance to the listening position is the same for both the left and right speakers. It is also recommended that the deviations of the distance from the listening position to L and R channel speakers (front left (FL) and front right (FR), surround left (SL) and surround right (SR), surround back left (SBL) and surround back right (SBR)) is less than 2 ft (60 cm).

The table below shows a typical speaker configuration for the AVP-A1HDCI.

 

FRONT

CENTER

SURROUND

SURROUND

SURROUND BACK

SUBWOOFER

 

 

 

 

A

 

B

 

 

 

(b)

 

L

R

 

L

 

R

L

 

R

L

R

1 only

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9.1-channels

S

S

S

S

 

S

S

 

S

S

S

–

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.1-channels

S

S

S

S

 

S

–

 

–

S

S

–

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.1-channels

S

S

S

S

 

S

–

 

–

–

–

S

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.1-channels

S

S

S

S

 

S

–

 

–

–

–

–

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.1-channels

S

S

S

–

 

–

–

 

–

–

–

–

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.1-channels

S

S

–

–

 

–

–

 

–

–

–

–

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2-channels

S

S

–

–

 

–

–

 

–

–

–

–

–

 

 

 

 

 

 

 

 

 

 

 

 

 

 

b The AVP-A1HDCI can be connected to a maximum of 3 subwoofers.

Connecting to the Power Amp

•Connect the AVP-A1HDCI pre-out terminal to the power amp (sold separately).

•AVP-A1HDCI has a RCA pre-out terminal and XLR pre-out terminal. Connect accordingly with the power amp you want to use.

•The polarity of the XLR pre-out terminal can be switched using GUI menu “Manual Setup” – “Option Setup” – “XLR Out Polarity” (vpage 39).

•Connect the speakers to the power amp.

•Refer to the owner’s manual of each piece of equipment when making connections.

POA-A1HDCI Connection and Operation

•When connecting the AVP-A1HDCI to the power amp POA-A1HDCI with a control link cable (included with the POA-A1HDCI), you can perform the following control operations.

•POA-A1HDCI channel input selection and power amp settings

•Link POA-A1HDCI to AVP-A1HDCI On/Standby control

•Link POA-A1HDCI meter operation to AVP-A1HDCI display on/off control (vpage 42)

•Updating POA-A1HDCI firmware (vpage 42)

•Up to 2 POA-A1HDCI units can be connected. Refer to the POA-A1HDCI owner's manual for making connections and POA-A1HDCI settings.

•For instructions for connecting speakers, please refer to the POA-A1HDCI owner’s manual.

•When using just one surround back speaker, connect it to the left channel (SBL).

Troubleshooting Information Zone-Multi Control Remote Playback Setup Connections Started Getting

10