Playback Setup Connections Started Getting

kTrigger Out 1

Select the conditions to turn on the trigger out 1 with respect to the zone, input source, surround mode, HDMI monitor, etc.

For details about the trigger out function, see page 23.

lTrigger Out 2

This sets the conditions to turn on the trigger out 2, in the same way as “Trigger Out 1” above.

A0Trigger Out 3

This sets the conditions to turn on the trigger out 3, in the same way as “Trigger Out 1” above.

A1Trigger Out 4

This sets the conditions to turn on the trigger out 4, in the same

Setting with Respect to the Monitor

 

 

 

 

 

 

A3Digital Out

When the HDMI monitor set to on is selected, the trigger out turns

Set usage of OPT4 OUT.

on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[Selectable items]

ZONE4 Select

 

Rec Select

 

This is effective when the “MAIN ZONE” has been set to “ON” for

NOTE

the “Setting with Respect to the Zone” and the input source which is

The ZONE4 operations cannot be performed when set to “Rec

set to “ON” has been selected for the “Setting with Respect to the

Select”.

Input Source”.

 

 

 

 

 

 

 

 

A4Remote ID

 

A2Transducer Setup

 

Set when using transducer.

 

Set remote control ID.

 

 

Match the ID setting of the remote control unit and the receiver.

 

 

 

 

 

 

 

Information Zone-Multi Control Remote

way as “Trigger Out 1” above.

[Selectable items]

ON

 

– – –

Setting with Respect to the Zone

When the power of the zone turned on/off, the trigger out turns on.

Setting with Respect to the Input Source

When the input source set to on is selected, the trigger out turns on.

Associated with respect to the input source for zones set to “ON” at “Setting with Respect to the Zone”.

The Transducer Setup can be accessed through GUI menu “Speaker Setup” - “Subwoofer Setup” is “1SP”, “2SP L/R” or “2SP MIX”. The transducer signal is outputted from “SW3”.

Level

[Variable range]

–12dB ~ 0dB ~ +12dB :

Set the transducer level.

OFF :

Turn the transducer output off.

[Selectable items] 1

2

3

4

•When changing the remote ID, also change the AMP, iPod, TU and NET/DTU modes of the main remote control unit at the same time (vpage 76).

•When changing the remote ID, also change the sub remote control unit at the same time (vpage 81).

A52Way Remote

Set when using the 2-way remote control unit.

Troubleshooting

Setting with Respect to the Surround Mode

When the surround mode set to on is selected, the trigger out turns on.

This is effective when the “MAIN ZONE” has been set to “ON” for the “Setting with Respect to the Zone” and the input source which is set to “ON” has been selected for the “Setting with Respect to the Input Source”.

When you adjust “Level”, the adjusted value is set for all surround modes. To adjust the level for individual surround modes, use “Channel Level” (vpage 72).

LPF

Set the upper limit of the low frequency output to the transducer.

[Selectable items]

40Hz 60Hz 80Hz 90Hz 100Hz 110Hz 120Hz

150Hz 200Hz 250Hz

[Selectable items] Used Not Used

When using a 2-way remote control unit (RC-7000CI and RC-7001RCI, sold separately), set this to “Used”.

NOTE

•When using the 2-way remote control unit, connect to the Port 1 RS-232C connector.

•If GUI menu “Manual Setup” - “Option Setup” - “2Way Remote”is set to “Used”, you cannot use port 1 of the RS-232C terminal for the external controller.

41