|
|
| Signal transmission |
|
|
| indicator |
| [ | AMP] | [MODE SELECTOR] |
| [ | TU] | |
[ | NET/DTU] | [ iPod] | |
|
|
| |
[NUMBER] 
[RC SETUP]
Setting the Remote ID
When using multiple DENON AV receivers in the same room, make this setting so that only the desired AV receiver operates.
1Press [AMP] to set the main remote control unit to the AMP mode.
2Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice.
3Refer to the table at the right, and use [NUMBER] to input the
ID to be changed.
The signal transmission indicator flashes twice.
4Press [TU], [iPod] or [NET/DTU] to select the mode to be set.
5Repeat steps 2 to 4 to set the remote IDs for all modes.
MODE |
|
| TUNER |
|
|
|
|
|
|
| ||||
SELECTOR |
|
|
|
| NET/DTU | |||||||||
|
|
|
|
|
|
|
|
| ||||||
| AMP |
|
|
|
|
|
| iPod |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| (MAIN) |
|
|
|
|
|
|
|
|
|
|
|
| |
| (Analog |
| (XM) |
|
|
|
|
|
|
| ||||
|
|
|
|
| (Net |
| (HD | |||||||
|
| TUNER) |
|
|
|
|
|
| ||||||
Remote ID |
|
|
|
|
|
| Audio) |
| Radio) | |||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 | 81001 | 52863 |
| 52864 |
| 72815 | 62865 |
| 62840 |
| ||||
(Default) |
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
2 | 82001 | 52795 |
| 52812 |
| 72816 | 62837 |
| 62841 |
| ||||
3 | 83001 | 52800 |
| 52813 |
| 72817 | 62838 |
| 62842 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 | 84001 | 52805 |
| 52814 |
| 72818 | 62839 |
| 62843 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE
•When changing a setting, be sure to set the same remote ID as the
•When changing the AMP mode’s remote ID, also change the “TUNER”, “iPod” and “NET/DTU” remote ID at the same time.
•Set the remote ID of an analog tuner for “TUNER” (
), the XM
remote ID for “
”.
Learning Function
If your AV devices are of a brand other than DENON or if they cannot be operated with the preset memory function, their remote control signals can be transfered to stored in the
1Press [MODE SELECTOR] for the device you want to set.
2Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice.
3Press [9], [7] and [5], in that order.
The signal transmission indicator flashes twice and the learning mode is set.
4Press the button to be set.
The main remote control unit’s display turns off.
bIf a button that cannot be learned is pressed, the signal transmission indicator lights but the signal is not learned.
5Point the main remote control units directly at each other and press and hold the button on the other
device’s remote control unit that you want to learn.
Once learning is completed normally, the display lights and the signal transmission indicator flashes twice.
Other device’s remote control unit
control unit
b If you want to learn other buttons, repeat steps 4 and 5. b The mode can be switched by pressing [MODE SELECTOR].
b The signal transmission indicator lights once for a long time if learning was not possible
6Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice and the setting is completed.
•With some remote control units, the signals cannot be learned or the device will not operate properly even when the signals have been learned. In this case, use the device’s own remote control unit.
•Learned buttons have priority over the preset memory. If you no longer need the learned setting, reset the learning function (vpage 78).
NOTE
•[HOME] cannot be learned.
•Do not learn any remote control signals at [RC SETUP].
•The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes cannot be learned.
Troubleshooting Information
76