Eaton Electrical 1250-3000 VA specs

Class A EMC Statements

(Low-Voltage Models)

FCC Part 15

NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

EN 62040-2

Some configurations are classified under EN 62040-2 as “Category C2 UPS.” For these configurations, the following applies:

WARNING This is a category C2 UPS product. In a residential environment, this product may cause radio interference, in which case the user may be required to take additional measures.

Class B EMC Statements

(High-Voltage Models)

FCC Part 15

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

SReorient or relocate the receiving antenna.

SIncrease the separation between the equipment and the receiver.

SConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

SConsult the dealer or an experienced radio/TV technician for help.

Image 3

Eaton Electrical 1250-3000 VA manual Class a EMC Statements Low-Voltage Models, Class B EMC Statements High-Voltage Models

Contents

Powerware 5130 Rack/Tower UPS 1250-3000 VA User’s Guide Requesting a Declaration of Conformity Class B EMC Statements High-Voltage Models Class a EMC Statements Low-Voltage Models Special Symbols Table of Contents Warranty Specifications Troubleshooting Chapter Introduction Backed by worldwide agency approvals Important Safety Instructions N G E RR N I N G R E Vigtige Sikkerhedsanvisninger GEM Disse AnvisningerU T I O N Sikkerhedsanvisninger V a a R Belangrijke Veiligheidsinstructies Bewaar Deze InstructiesV a R S E L Belangrijke Veiligheidsinstructies G E L E T R O I T U S Tärkeitä Turvaohjeita Suomi Säilytä Nämä OhjeetTarkeita Turvaohjeita A R a Consignes de sécurité Consignes DE Sécurité Importantes Conserver CES Instructions H T U N G Wichtige Sicherheitsanweisungen AufbewarenSicherheitswarnungen R N U N G R I C O L O Avvisi di sicurezza T E N Z I O N E V E R T E N Z a Viktige Sikkerhetsinstruksjoner Gjem Disse Instruksjonene Viktig SikkerhetsinformasionR L I G I D a D O Instruções DE Segurança Importantes Guarde Estas InstruçõesR S I K T I G Regulamentos de Segurança R I G O Предупреждения по мерам безопасностиОпасно Осторожно Предупреждение Advertencias de Seguridad L I G R OV E R T E N C I a R a Viktiga Säkerhetsföreskrifter Spara Dessa FöreskrifterE C a U C I Ó N Säkerhetsföreskrifter K T I G T Inspecting the Equipment Chapter Installation 2U models only Checking the Accessory KitUPS Accessory Kit ItemDescription Additional High-Voltage Model Accessory Items EBM Accessory ItemsVA models only Connecting the Internal Battery Connectors Connecting the UPS Internal Battery Rackmount Setup UPS Setup Installing the Rail Kit Tower Setup Continue to the following section, Installing the UPS Installing the Joining Brackets UPS Installation with Four EBMs Installing the UPS Installing a Communication Cable Installing the Power and Equipment Cords High-voltage only RPO/ROO Connection RPO and ROO Installation Contact 1750 VA, Low-Voltage Rear Panel UPS Rear Panels Rear Panel Turning the UPS On Chapter Operation Turning the UPS Off Starting the UPS on Battery UPS Front Panel Operating Modes Battery Mode USB Port Additional UPS Features USB Port Pin Number Function Contact Communication Port optional Programmable Receptacle Load Segments PowerShare Voltage Threshold Options Customizing the UPS with the UPS Configuration ToolFunction Factory Setting Other Available Settings Main Output Options Battery Options UPS Sensitivity OptionsUPS On/Off Options Transporting the UPS UPS and Battery Care When to Replace Batteries Storing the UPS and BatteriesReplacing Batteries How to Replace Internal Batteries Unscrew and remove the metal battery cover see Figure How to Replace Extended Battery Modules Recycling the Used Battery or UPS Low-Voltage Model Specifications Dimensions WxHxD Weight High-Voltage Model SpecificationsWeights and Dimensions Power Levels Power Connections EBM Model Number Dimensions WxHxD WeightModel Battery Environmental and Safety Full Load Battery RuntimesHalf Load +1 EBM +2 EBMs +3 EBMs +4 EBMs Specifications Alarm Indicators Audible Alarms and UPS Conditions Alarm or Condition Possible Cause Action Troubleshooting Guide Desk for the dealer or distributor nearest you Service and Support Troubleshooting Two-Year Limited Warranty US and Canada Chapter Warranty Warranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty Page 1642017302