Important Safety Instructions | Eaton Electrical 1250-3000 VA

Chapter 2 Safety Warnings

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during installation and maintenance of the UPS and batteries. Please read all instructions before operating the equipment and save this manual for future reference.

D A N G E R

This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the UPS.

W A R N I N G

SThis UPS contains its own energy source (batteries). The output receptacles may carry live voltage even when the UPS is not connected to an AC supply.

SFor 230V models, the output receptacles may remain electrically live. If the input power source in your application is wired line-to-neutral (as in most European applications), the voltage to the output receptacles is 0V. With line-to-line input wiring, the voltage to the output receptacles is 115V (measured from line-to-ground or line-to-neutral, depending on the UPS wiring).

SDo not remove or unplug the input cord when the UPS is turned on. This removes the safety ground from the UPS and the equipment connected to the UPS.

STo reduce the risk of fire or electric shock, install this UPS in a temperature and humidity controlled, indoor environment, free of conductive contaminants. Ambient temperature must not exceed 40°C (104°F). Do not operate near water or excessive humidity (95% maximum).

STo comply with international standards and wiring regulations, the total equipment connected to the output of this UPS must not have an earth leakage current greater than 3.5 milliamperes.

EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2	3
www.powerware.com

Image 9

Eaton Electrical 1250-3000 VA manual Important Safety Instructions, N G E R, R N I N G

Contents

Powerware 5130 Rack/Tower UPS 1250-3000 VA User’s Guide Requesting a Declaration of Conformity Class B EMC Statements High-Voltage Models Class a EMC Statements Low-Voltage Models Special Symbols Table of Contents Warranty Specifications Troubleshooting Chapter Introduction Backed by worldwide agency approvals Important Safety Instructions N G E RR N I N G U T I O N Vigtige Sikkerhedsanvisninger GEM Disse AnvisningerSikkerhedsanvisninger R E V a R S E L Belangrijke Veiligheidsinstructies Bewaar Deze InstructiesBelangrijke Veiligheidsinstructies V a a R G E L E T Tarkeita Turvaohjeita Tärkeitä Turvaohjeita Suomi Säilytä Nämä OhjeetA R a R O I T U S Consignes de sécurité Consignes DE Sécurité Importantes Conserver CES Instructions Sicherheitswarnungen Wichtige Sicherheitsanweisungen AufbewarenR N U N G H T U N G R I C O L O Avvisi di sicurezza T E N Z I O N E V E R T E N Z a Viktige Sikkerhetsinstruksjoner Gjem Disse Instruksjonene Viktig SikkerhetsinformasionR L I G R S I K T I G Instruções DE Segurança Importantes Guarde Estas InstruçõesRegulamentos de Segurança I D a D O R I G O Предупреждения по мерам безопасностиОпасно Осторожно Предупреждение Advertencias de Seguridad L I G R OV E R T E N C I a E C a U C I Ó N Viktiga Säkerhetsföreskrifter Spara Dessa FöreskrifterSäkerhetsföreskrifter R a K T I G T Inspecting the Equipment Chapter Installation UPS Accessory Kit Checking the Accessory KitItemDescription 2U models only Additional High-Voltage Model Accessory Items EBM Accessory ItemsVA models only Connecting the Internal Battery Connectors Connecting the UPS Internal Battery Rackmount Setup UPS Setup Installing the Rail Kit Tower Setup Continue to the following section, Installing the UPS Installing the Joining Brackets UPS Installation with Four EBMs Installing the UPS Installing a Communication Cable Installing the Power and Equipment Cords High-voltage only RPO/ROO Connection RPO and ROO Installation Contact 1750 VA, Low-Voltage Rear Panel UPS Rear Panels Rear Panel Turning the UPS On Chapter Operation Turning the UPS Off Starting the UPS on Battery UPS Front Panel Operating Modes Battery Mode USB Port Additional UPS Features USB Port Pin Number Function Contact Communication Port optional Programmable Receptacle Load Segments PowerShare Function Factory Setting Other Available Settings Customizing the UPS with the UPS Configuration ToolMain Output Options Voltage Threshold Options Battery Options UPS Sensitivity OptionsUPS On/Off Options Transporting the UPS UPS and Battery Care When to Replace Batteries Storing the UPS and BatteriesReplacing Batteries How to Replace Internal Batteries Unscrew and remove the metal battery cover see Figure How to Replace Extended Battery Modules Recycling the Used Battery or UPS Low-Voltage Model Specifications Weights and Dimensions High-Voltage Model SpecificationsPower Levels Dimensions WxHxD Weight Power Connections EBM Model Number Dimensions WxHxD WeightModel Battery Environmental and Safety Half Load Battery Runtimes+1 EBM +2 EBMs +3 EBMs +4 EBMs Full Load Specifications Alarm Indicators Audible Alarms and UPS Conditions Alarm or Condition Possible Cause Action Troubleshooting Guide Desk for the dealer or distributor nearest you Service and Support Troubleshooting Two-Year Limited Warranty US and Canada Chapter Warranty Warranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty Page 1642017302