World Class 3000
Instruction Manual
Table 5-5. SETUP Sub-Menu (continued)
|
|
|
|
|
|
|
| |
SELECTION |
| PARAMETERS |
| DESCRIPTION |
|
| ||
Relay |
|
|
|
|
|
|
|
|
Outputs |
|
|
|
|
|
|
|
|
|
|
|
|
| NOTE |
|
| |
| K1 and K2 relay outputs can be configured for "OFF" or any one of the eight |
|
| |||||
| events listed below. Up to three events can control each relay output. Events are |
|
| |||||
| selected in the SETUP |
|
|
|
| |||
K1 Setup |
|
| - | Off |
| No effect. |
|
|
|
| Event 1 | 1. | In Cal |
| Probe goes into calibration status. |
|
|
|
| Event 2 | 2. | Hi O2 |
| Output exceeds high end alarm limit. |
|
|
|
| Event 3 | 3. | Lo O2 |
| Output goes below low alarm limit. |
|
|
K2 Setup |
| Event 1 | 4. | Htr Fail |
| Probe heater fault occurs. |
|
|
| Event 2 | 5. | Cal Fail |
| Probe failed last calibration. |
|
| |
|
| Event 3 | 6. | TG Low |
| Calibration gas pressure gets too low. |
|
|
|
|
| 7. | Cell Res |
| Probe resistance exceeds high limit. |
|
|
|
|
| 8. | High Range |
| High analog output range is selected. |
|
|
|
|
|
|
|
| |||
Analog |
| SOURCE | O2 |
|
| Select the measurement value to be represented on |
|
|
Output |
|
| Efficiency |
| the analog output. |
| 5 | |
|
|
| Dual Rng O2 |
|
|
| ||
|
|
|
|
| ||||
|
| AOUT TYPE |
|
|
|
|
| |
|
|
|
| Select one of the listed options to define upper and |
|
| ||
|
|
| HART |
| lower limits of probe analog output. Only a selection |
|
| |
|
|
|
| that matches the position of the analog output selector |
|
| ||
|
|
|
| switch on the microprocessor board (Figure |
|
| ||
|
|
|
|
|
| be accepted. The defined limits correspond to the |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| menu. |
|
|
|
| RANGE SETUP |
|
|
|
|
| |
|
| (Source not set to Dual Rng O2) |
|
|
|
| ||
|
| Xfer Fnct | Log |
|
| Select the transfer function used on the analog output. |
|
|
|
|
| Lin |
|
| Selecting Log will not effect the output when Efficiency |
|
|
|
|
|
|
|
| is selected as the Source. |
|
|
|
| Range Values |
|
|
|
|
| |
|
| High End |
|
| Enter the upper and lower analog output range values. |
|
| |
|
| 0.000% O2 - 25.00% O2 |
| The High End value defines the measured O2 value |
|
| ||
|
| Low End |
|
| corresponding to the high analog output value, i.e., |
|
| |
|
|
|
| 20mA or 10V, and the Low End value corresponds to |
|
| ||
|
| 0.000% O2 - 25.00% O2 |
|
|
| |||
|
|
| the low analog output value, i.e., 0mA, 4mA, or 0V. |
|
| |||
|
|
|
|
|
|
|
| |
Rosemount Analytical Inc. A Division of Emerson Process Management | General User Interface (GUI) Operation |
