5HIHUHQFH 0DQXDO￿

00809-0100-4811, Rev AA

October)"￿￿￿￿￿￿2002￿"￿￿￿￿￿￿￿￿￿

 

Rosemount 3300 Series

 

 

 

 

 

 

 

 

 

 

 

Table C-2. HART Communicator Diagnostic Messages

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Requests permission to overwrite existing configuration either by a device-to-memory transfer or by

 

)I￿

 

 

 

 

an offline configuration. User answers using the softkeys.

 

 

 

 

 

 

 

 

 

 

 

 

 

Press the OK softkey. This message usually appears after an error message from the application or

￿￿

 

￿""￿N

 

as a result of HART communications.

 

 

 

 

 

 

 

 

 

 

 

 

 

The edited value that was sent to a device was not properly implemented. Restoring the device value

￿￿￿"￿￿￿

 

￿￿￿￿

 

returns the variable to its original value.

 

 

 

 

 

"￿￿￿￿￿￿￿￿

 

 

 

Prompts user to press SAVE softkey to initiate a device-to-memory transfer.

 

 

 

 

 

 

4

 

 

￿￿"

 

Data is being transferred from a device to configuration memory.

 

 

 

 

 

 

 

<￿

 

 

;

"￿4￿￿￿￿￿￿;￿￿￿

 

Data is being transferred from configuration memory to a device.

 

 

 

 

 

 

 

 

 

 

 

 

 

There are write-only variables which have not been set by the user. These variables should be set or

;

￿￿

￿￿

 

N

 

invalid values may be sent to the device.

 

 

 

 

 

 

 

 

 

 

 

 

 

Press YES to send unsent data and turn the HC off. Press NO to turn the HC off and lose the unsent

 

 

￿￿;

"￿￿￿

 

data.

 

 

 

 

 

 

(

￿!)4￿￿￿￿￿

 

 

 

Command returns fewer data bytes than expected as determined by the device description.

 

 

 

 

 

;￿￿

Q"<

-￿￿￿$)￿￿￿￿￿￿￿￿￿￿"￿￿￿;￿￿￿￿B￿￿￿￿￿￿￿￿￿

 

Device returns a command response indicating a fault with the connected device.

 

 

 

 

 

 

 

 

 

 

 

 

 

The engineering units for this variable have been edited. Send engineering units to the device before

4￿$

 

 

 

￿"

 

editing this variable.

 

 

 

 

 

 

 

 

 

 

 

 

 

There is unsent data for a previously connected device which must be sent or thrown away before

<￿￿￿￿5￿￿￿B￿￿

 

￿￿￿￿

 

connecting to another device.

 

 

 

 

 

 

 

>

 

 

 

 

 

Gives direction to change the contrast of the HC display.

 

 

 

 

 

 

 

 

 

 

 

 

 

The user-entered value is either not within the range for the given type and size of variable or not

￿￿￿￿

￿5￿￿￿￿￿￿"￿￿￿￿￿Q"

;￿￿￿￿￿￿￿￿;￿B

 

within the min/max specified by the device.

 

 

 

 

 

 

 

 

 

 

 

 

 

Either a read/write command indicates too few data bytes received, transmitter fault, invalid response

 

 

 

 

 

 

code, invalid response command, invalid reply data field, or failed pre- or post-read method; or a

￿￿Q"￿

;￿;B<-

;

￿￿￿￿￿

 

response code of any class other than SUCCESS is returned reading a particular variable.

 

 

 

 

 

 

 

 

 

 

 

 

 

A variable related to this variable has been edited. Send related variable to the device before editing

 

 

 

 

 

 

this variable.

 

 

 

 

 

 

 

C-11

Page 123
Image 123
Emerson Process Management rosemount 3300 series manual Table C-2. Hart Communicator Diagnostic Messages