Host-to-Switcher Instructions | Extron electronic 1616, 84, 1212, 124

Front panel Configuration port

This port is hardwired for RS-232 only.

The optional 9-pin D to 2.5 mm mini jack TRS RS-232 cable, part #70-335-01(figure 4-2) can be used for connection to the Configuration port.

1 6

9

5

6 feet

(1.8 m)

Part #70-335-01

Tip

Ring

Sleeve (Gnd)

9-pin D	Connection	TRS Plug
Pin 2	Computer's RX line	Tip
Pin 3	Computer's TX line	Ring
Pin 5	Computer's signal ground	Sleeve

Figure 4-2 — Optional 9-pin TRS RS-232 cable

This port is independent of the rear panel Remote port and is not affected by changes to the rear panel port’s protocol. This front panel port’s protocol can be changed, under SIS command control only. See the Command/Response table for IP SIS commands, later in this chapter, to configure both ports under SIS control.

Host-to-Switcher Instructions

The switcher accepts SIS (Simple Instruction Set) commands through either serial port. SIS commands consist of one or more characters per command field. They do not require any special characters to begin or end the command character sequence. Each switcher response to an SIS command ends with a carriage return and a line feed (CR/LF = ), which signals the end of the response character string. A string is one or more characters.

CrossPoint 300 Matrix Switchers • Programmer’s Guide

4-3

Image 73

Extron electronic 1616, 84, 1212, 124, 168, 128, 816, 88 manual Host-to-Switcher Instructions, Front panel Configuration port

Contents

CrossPoint 300 Series Matrix Switchers Consignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad Español CrossPoint 300 Matrix Switchers Quick Start QS-1 Quick Start CrossPoint 300 Matrix Switchers Save or recall a preset Quick Start CrossPoint 300 Matrix Switchers, cont’dView, adjust the audio level QS-2 CrossPoint 300 Matrix Switchers Quick Start Table of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One CrossPoint 300 Matrix Switchers Introduction About the Matrix SwitchersIntroductiontroduction, cont’d About this Manual Extron CrossPoint 300 128 HVA Definitions Introduction, cont’d Features CrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two Mounting the Switcher Installationstallation, cont’dCrossPoint 300 Matrix Switchers Installation UL requirements Shows the CrossPoint 300 128 HVA Connections and Rear Panel Features Rgbhv input and output Installation, cont’dAudio input and output HVA models only Typical audio connectors Remote RS-232/RS-422 port Reset button Power Sync termination switches Front panel configuration port Front Panel Configuration Port CrossPoint 300 Matrix Switchers Installation Installation, cont’d Three CrossPoint 300 Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d Input and output buttons Definitions Control buttons Operation, cont’d CrossPoint 300 Matrix Switchers Operation Controls Front panel security lockouts Front Panel Operations Creating a configuration Power indications Clear all selections Example 1 Creating a set of video and audio ties Example 2 Adding a tie to a set of video and audio ties Press and release the Enter button figure 10 Clear all selections Example 3 Removing a tie from a set of video and audio ties Press and release the Enter button figure 16 Clear all selections 19 Deselect the output 22 Clear all selections Viewing a configuration 23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio 29 Select Rgbhv and audio 31 Unmute the outputs Using global presets LED blinks figure Example 6 Saving a preset Press and release the Preset button figure Example 7 Recalling a preset 39 Select the preset CrossPoint 300 Series Switcher Viewing and adjusting the input audio level HVA models 42 Clear all selections Example 8 Viewing and adjusting an input audio level Audio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Press and release the Audio button figure Viewing and adjusting the output volume HVA models Reading the displayed value Push Esc button nineteen times 10% + 191.5% = 38.5% volume Audio output volume settings 49 Clear all selections Example 9 Viewing and adjusting an output volume level 51 Select output 54 Volume display on a 16-output-button switcher Setting the front panel locks Executive modes 56 Toggle front panel lock on or off Selecting Lock mode 2 or toggling between mode 2 and mode Power Performing a system reset from the front panel Selecting the rear panel Remote port protocol and baud rate Control Control I/O Enter Preset View ESC Rgbhv Audio 60 RS-232/RS-422 and baud rate selection Rear Panel Operations Performing a system reset from the rear panel Performing a hard reset from the rear panel Optimizing the Audio HVA Switchers Plasma display S-video problem TroubleshootingGeneral checks Worksheet example 1 Entering system equipment Configuration Worksheets Worksheet example 2 Drawing ties 65 Worksheet example 2 Status meeting configuration 66 Worksheet example 3 Test configuration Worksheet example 3 Test configuration Preset # Matrix Switchers Configuration Worksheet This page was intentionally left blank Four Programmer’ser’sGuide,Guidecont’d CrossPoint 300 Matrix Switchers Programmer’s GuideSerial Ports Rear panel Remote port Front panel Configuration port Host-to-Switcher Instructions Programmer’s Guide, cont’d Switcher-Initiated Messages Using the Command/Response Table Switcher Error Responses Symbol Definitions Command/Response Table for SIS Commands Command Ascii Command Response Additional description Command/response table for SIS commands Command/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Response Additional description Command Serial port configuration Five Installing the software Matrix Switchers Control ProgramCrossPoint 300 Matrix Switchers Matrix Software MatrixSoftware,cont’d Comm port selection window Using the software Matrix Software, cont’d Extron Matrix Switchers Control Program window no ties Sample program window with ties Updating the firmware Open window CrossPoint 300 Matrix Switchers Matrix Software Windows menus Windows buttons, drop boxes, and trashFile menu Status window Tools menu Preferences menu Audio-input Configure selection Using the help system Using emulation modeButton-Label Generator 13 Extron’s Button-Label Generator window AAppendix a CrossPoint 300 Matrix Switchers Reference Information SpecificationsReferenceInformation,co t’d Sync Reference Information, cont’d Control/remote switcher Part Numbers Optional accessoriesCrossPoint 300 part numbers Included parts Button Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C