Programmer’s Guide, cont’d | Extron electronic 1212, 84, 1616, 124, 88

Programmer’s Guide, cont’d

Switcher-Initiated Messages

When a local event such as a front panel operation occurs, the switcher responds by sending a message to the host. The switcher-initiated messages are listed below (underlined).

(c) Copyright 2007, Extron Electronics, CP 300 450 MAV IP, Vx.xx, 60-nnn-nn

The switcher initiates the copyright message when it is first powered on. Vx.xx is the firmware version number and 60-nnn-nnis the switcher part number.

Qik

The switcher initiates the Qik message when a front panel switching operation or preset recall has occurred.

Sprnn

The switcher initiates the Spr message when a memory preset has been saved from the front panel. “nn” is the preset number.

Rprnn

The switcher initiates the Rpr message when a memory preset has been recalled from the front panel. “nn” is the preset number.

Innn Audxx

The switcher initiates the Aud message when a front panel input audio level change has occurred. “nn” is the input number and “xx” is the dB level.

Vmtnn•x

The switcher initiates the Vmt message when a video output mute is toggled on or off from the front panel. “nn” is the output number, • is a space, and “x” is the mute status: 1 = on, 0 = off.

Amtnn•x

The switcher initiates the Amt message when an audio output mute is toggled on or off from the front panel. “nn” is the output number, • is a space, and “x” is the mute status: 1 = on, 0 = off.

Exen

The switcher initiates the Exe message when front panel lock is toggled on or off from the front panel. “n” is the front panel lock status: 1 = on, 0 = off.

4-4 CrossPoint 300 Matrix Switchers • Programmer’s Guide

Image 74

Extron electronic 1212, 84, 1616, 124, 168, 128, 816, 88 manual Programmer’s Guide, cont’d, Switcher-Initiated Messages

Contents

Matrix Switchers CrossPoint 300 Series Sicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad Español Quick Start CrossPoint 300 Matrix Switchers CrossPoint 300 Matrix Switchers Quick Start QS-1 View, adjust the audio level Quick Start CrossPoint 300 Matrix Switchers, cont’dSave or recall a preset QS-2 CrossPoint 300 Matrix Switchers Quick Start Table of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One Introductiontroduction, cont’d About the Matrix SwitchersCrossPoint 300 Matrix Switchers Introduction About this Manual Definitions Extron CrossPoint 300 128 HVA Features Introduction, cont’d CrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two CrossPoint 300 Matrix Switchers Installation Installationstallation, cont’dMounting the Switcher UL requirements Connections and Rear Panel Features Shows the CrossPoint 300 128 HVA Audio input and output HVA models only Installation, cont’dRgbhv input and output Typical audio connectors Reset button Remote RS-232/RS-422 port Sync termination switches Power Front Panel Configuration Port Front panel configuration port CrossPoint 300 Matrix Switchers Installation Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint 300 Matrix Switchers Operation Definitions Input and output buttons Operation, cont’d Control buttons CrossPoint 300 Matrix Switchers Operation Controls Front Panel Operations Front panel security lockouts Power indications Creating a configuration Example 1 Creating a set of video and audio ties Clear all selections Press and release the Enter button figure Example 2 Adding a tie to a set of video and audio ties 10 Clear all selections Press and release the Enter button figure Example 3 Removing a tie from a set of video and audio ties 16 Clear all selections 19 Deselect the output Viewing a configuration 22 Clear all selections 23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 29 Select Rgbhv and audio Using global presets 31 Unmute the outputs Example 6 Saving a preset LED blinks figure Example 7 Recalling a preset Press and release the Preset button figure 39 Select the preset Viewing and adjusting the input audio level HVA models CrossPoint 300 Series Switcher Example 8 Viewing and adjusting an input audio level 42 Clear all selections Audio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Viewing and adjusting the output volume HVA models Press and release the Audio button figure Push Esc button nineteen times 10% + 191.5% = 38.5% volume Reading the displayed value Audio output volume settings Example 9 Viewing and adjusting an output volume level 49 Clear all selections 51 Select output Setting the front panel locks Executive modes 54 Volume display on a 16-output-button switcher Selecting Lock mode 2 or toggling between mode 2 and mode 56 Toggle front panel lock on or off Performing a system reset from the front panel Power Control Control I/O Enter Preset View ESC Rgbhv Audio Selecting the rear panel Remote port protocol and baud rate 60 RS-232/RS-422 and baud rate selection Performing a system reset from the rear panel Rear Panel Operations Optimizing the Audio HVA Switchers Performing a hard reset from the rear panel General checks TroubleshootingPlasma display S-video problem Configuration Worksheets Worksheet example 1 Entering system equipment 65 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing ties Worksheet example 3 Test configuration 66 Worksheet example 3 Test configuration Matrix Switchers Configuration Worksheet Preset # This page was intentionally left blank Four Serial Ports CrossPoint 300 Matrix Switchers Programmer’s GuideProgrammer’ser’sGuide,Guidecont’d Rear panel Remote port Host-to-Switcher Instructions Front panel Configuration port Switcher-Initiated Messages Programmer’s Guide, cont’d Switcher Error Responses Using the Command/Response Table Command/Response Table for SIS Commands Symbol Definitions Command/response table for SIS commands Command Ascii Command Response Additional description Command/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Command Response Additional description Serial port configuration Five CrossPoint 300 Matrix Switchers Matrix Software Matrix Switchers Control ProgramInstalling the software MatrixSoftware,cont’d Using the software Comm port selection window Extron Matrix Switchers Control Program window no ties Matrix Software, cont’d Updating the firmware Sample program window with ties Open window CrossPoint 300 Matrix Switchers Matrix Software File menu Windows buttons, drop boxes, and trashWindows menus Tools menu Status window Audio-input Configure selection Preferences menu Button-Label Generator Using emulation modeUsing the help system 13 Extron’s Button-Label Generator window AAppendix a ReferenceInformation,co t’d SpecificationsCrossPoint 300 Matrix Switchers Reference Information Sync Control/remote switcher Reference Information, cont’d CrossPoint 300 part numbers Optional accessoriesPart Numbers Included parts Button Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C