CrossPoint 300 Matrix Switchers Installation | Extron electronic 88

This port is RS-232 only, with its default protocols as follows:

•	9600 baud	•	no parity	• 8 data bits
•	1 stop bit	•	no flow control

The maximum distances from the matrix switcher to the controlling device can vary up to 200 feet (61 m). Factors such as cable gauge, baud rates, environment, and output levels (from the switcher and the controlling device) all affect transmission distance. Distances of about 50 feet (15 m) are typically not a problem. In some cases the matrix switcher may be capable of serial communications via RS-232 up to 250 feet (76 m) away.

CrossPoint 300 Matrix Switchers • Installation

2-9

Image 23

Extron electronic 88, 84, 1616, 1212, 124, 168, 128, 816 manual CrossPoint 300 Matrix Switchers Installation

Contents

CrossPoint 300 Series Matrix Switchers Instrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch CrossPoint 300 Matrix Switchers Quick Start QS-1 Quick Start CrossPoint 300 Matrix Switchers QS-2 CrossPoint 300 Matrix Switchers Quick Start Quick Start CrossPoint 300 Matrix Switchers, cont’dSave or recall a preset View, adjust the audio level Table of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One About this Manual About the Matrix SwitchersCrossPoint 300 Matrix Switchers Introduction Introductiontroduction, cont’d Extron CrossPoint 300 128 HVA Definitions Introduction, cont’d Features CrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two UL requirements Installationstallation, cont’dMounting the Switcher CrossPoint 300 Matrix Switchers Installation Shows the CrossPoint 300 128 HVA Connections and Rear Panel Features Audio input and output HVA models only Installation, cont’dRgbhv input and output Typical audio connectors Remote RS-232/RS-422 port Reset button Power Sync termination switches Front panel configuration port Front Panel Configuration Port CrossPoint 300 Matrix Switchers Installation Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint 300 Matrix Switchers Operation Input and output buttons Definitions Control buttons Operation, cont’d CrossPoint 300 Matrix Switchers Operation Controls Front panel security lockouts Front Panel Operations Creating a configuration Power indications Clear all selections Example 1 Creating a set of video and audio ties Example 2 Adding a tie to a set of video and audio ties Press and release the Enter button figure 10 Clear all selections Example 3 Removing a tie from a set of video and audio ties Press and release the Enter button figure 16 Clear all selections 19 Deselect the output 22 Clear all selections Viewing a configuration 23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio 29 Select Rgbhv and audio 31 Unmute the outputs Using global presets LED blinks figure Example 6 Saving a preset Press and release the Preset button figure Example 7 Recalling a preset 39 Select the preset CrossPoint 300 Series Switcher Viewing and adjusting the input audio level HVA models 42 Clear all selections Example 8 Viewing and adjusting an input audio level Audio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Press and release the Audio button figure Viewing and adjusting the output volume HVA models Reading the displayed value Push Esc button nineteen times 10% + 191.5% = 38.5% volume Audio output volume settings 49 Clear all selections Example 9 Viewing and adjusting an output volume level 51 Select output 54 Volume display on a 16-output-button switcher Setting the front panel locks Executive modes 56 Toggle front panel lock on or off Selecting Lock mode 2 or toggling between mode 2 and mode Power Performing a system reset from the front panel Selecting the rear panel Remote port protocol and baud rate Control Control I/O Enter Preset View ESC Rgbhv Audio 60 RS-232/RS-422 and baud rate selection Rear Panel Operations Performing a system reset from the rear panel Performing a hard reset from the rear panel Optimizing the Audio HVA Switchers General checks TroubleshootingPlasma display S-video problem Worksheet example 1 Entering system equipment Configuration Worksheets Worksheet example 2 Drawing ties 65 Worksheet example 2 Status meeting configuration 66 Worksheet example 3 Test configuration Worksheet example 3 Test configuration Preset # Matrix Switchers Configuration Worksheet This page was intentionally left blank Four Rear panel Remote port CrossPoint 300 Matrix Switchers Programmer’s GuideProgrammer’ser’sGuide,Guidecont’d Serial Ports Front panel Configuration port Host-to-Switcher Instructions Programmer’s Guide, cont’d Switcher-Initiated Messages Using the Command/Response Table Switcher Error Responses Symbol Definitions Command/Response Table for SIS Commands Command Ascii Command Response Additional description Command/response table for SIS commands Command/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Response Additional description Command Serial port configuration Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software CrossPoint 300 Matrix Switchers Matrix Software Comm port selection window Using the software Matrix Software, cont’d Extron Matrix Switchers Control Program window no ties Sample program window with ties Updating the firmware Open window CrossPoint 300 Matrix Switchers Matrix Software File menu Windows buttons, drop boxes, and trashWindows menus Status window Tools menu Preferences menu Audio-input Configure selection Button-Label Generator Using emulation modeUsing the help system 13 Extron’s Button-Label Generator window AAppendix a ReferenceInformation,co t’d SpecificationsCrossPoint 300 Matrix Switchers Reference Information Sync Reference Information, cont’d Control/remote switcher Included parts Optional accessoriesPart Numbers CrossPoint 300 part numbers Button Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C