Manuals / Extron electronic / Computer Equipment / Network Card

Extron electronic IPL T PCS4i manual Installation and Rear Panels, Installation Overview

Models: IPL T PCS4 IPL T PCS4i

1 69

Download 69 pages 31.92 Kb

Page 10

Installation and

Installation and

Rear Panels

This section contains installation and cabling instructions for the PCS4. The following topics are discussed:

•Installation Overview

•Rear Panels

•Setting Up the LAN Port

•Connecting the Devices

Installation Overview

To install and set up an IPL T PCS4 interface, follow these steps:

1.Turn off all of the equipment. Make sure that the video sources (DSS, cable boxes, or other devices), the IPL interface, the output devices (monitors, VCRs, projectors, and so on), and the controller are all turned off and disconnected from the power source.

2.If desired, mount the PCS4 interface (see “Mounting the IPL T PCS4 Interface” in the “Reference Material” section).

3.Plug the PCS4 power cord into an AC outlet. For the 120 VAC version, use the supplied 14 AWG IEC power cord (part number 27-407-01).

4.Connect an active LAN Ethernet cable to the RJ-45 port on the rear panel to establish a link to the network.

5.Set up an IP address for the PCS4 (see “HTML Configuration and Control” or “SIS Programming and Control”).

6.Plug the desired devices into the power receptacles on the PCS4 rear panel.

7.Press the front panel buttons to power on the receptacles.

8.Turn on the output devices.

9.Configure the PCS4 interface through the front panel, Telnet, or the web pages, then access the unit using an Internet browser.

IPL T PCS4 • Installation and Rear Panel

4

Image 10

Extron electronic IPL T PCS4i manual Installation and Rear Panels, Installation Overview, Connecting the Devices

Contents

User Guide IPL T PCS4 IPL T PCS4iIP Link Power Control Interfaces IP LinkSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolFCC Class A Notice Notifications Software CommandsConventions Used in this Guide CopyrightFront Panel Features and Operation ContentsIPL T PCS4 Contents HTML Configuration and ControlIPL T PCS4 Contents Introduction FeaturesAbout this Guide About the IPL T PCS4 Features Application Diagrams About this GuideApplication Diagrams Alarm Codec Camera Monitor Projector Figure 2. Connection Diagram for IPL T PCS4iPower Control with Sensing Capabilities IPL T PCS4 IntroductionInstallation Overview Rear Panels Setting Up the LAN Port Installation and Rear PanelsInstallation Overview Connecting the DevicesRear Panels Figure 5. IPL T PCS4i Rear Panel 220 VACConfiguring the LAN Port Setting Up the LAN PortConnecting the Devices RJ-45 ConnectorPage Front Panel Features Setting Up the System Using the Front Panel Front Panel Features and OperationFront Panel Features Resetting the UnitSetting Up Power Control Setting Up the System Using the Front PanelSetting Power Level Reference Thresholds Setting the Full power threshold If the receptacle is set to And the power levelNone and Not Set thresholds The receptacleGrouping Receptacles Front panel Security Lockout Executive ModeS LED lit - Group F LED lit - Group Red power LED lit - Group Clearing thresholdsMode Resetting the UnitFigure 8. Reset Button ActivationMode ModeMode ActivationSetting Up the Computer Using ARP HTML Configuration and ControlConfiguring the Hardware Configuring the Hardware Using the Embedded Web PagesFigure 9. ARP-S Command Screen IPL T PCS4 LAN port defaults PCS4 IP address Gateway IP address Setting Up the Computer Using a Web BrowserFigure 10. Screen Showing the Ping Command Subnet mask DHCP Off Link speed and duplex level Auto detectedSetting up the computer for IP communication Subnet mask Default gateway Blank or Configuring the IPL T PCS4 using a web browser Figure 11. Example of a Default System Settings PageUsing the Embedded Web Pages Figure 12. Password Prompt WindowViewing the System Status Figure 13. System Status Web PageFigure 14. System Settings Screen on the Configuration Tab ConfigurationSpecifying system settings IP settingsDate and time settings To assign passwords Assigning passwordsRemoving passwords Entering e-mail addresses for alerts Figure 16. E-mail Alerts Screen Upper PortionUpgrading firmware Figure 17. Firmware Upgrade ScreenManaging receptacles Switching power to receptacles on and off Figure 18. Switching/Grouping ScreenGrouping receptacles Monitoring Settings section Monitoring the receptacles and setting the alarmFigure 19. Monitor Screen Alarm Relay Settings section Scheduling power to receptacles Scheduling an individual receptacleScheduling receptacles by day of the week All receptacles on and offFile Management One receptacle, power on or offFigure 23. File Management Screen with Two Files Uploaded Adding a directory Uploading files to the web pageOther file management functions Server Side Includes SSIs Figure 24. Example of SSI CommandCustom Web Pages #echo var=Code example URL with a Query String Using an SIS CommandFigure 25. Example of a Query String Command Figure 26. Web Page HTML Source Code Document Showing SSIsFigure 28. Browser View of Previous HTML Source Code URL EncodingFigure 29. Characters that Do Not Require Encoding Characters Reserved charactersUnsafe characters Figure 30. Reserved CharactersFigure 32. Telnet Command Prompt A/V Device Power ControlAccessing and Using Telnet Port Custom Web PagesPower Connections TroubleshootingFigure 33. Connecting to the IP Address Figure 35. Response to an Unsuccessful Ping Command Figure 34. Successful Ping Command ResponseNetwork Connections Downloading Global Configurator Software SIS Programming and Control Host-to-Interface Communication Using the Command and Response TableSymbol Definitions Command and Response Table for SIS Commands Host-to-Interface CommunicationError Responses Password InformationError Response References Telnet Using the Command and Response TableFigure 36. ASCII to Hex Conversion Table Web BrowserSymbol Definitions Examplefor example IPL-T-PCS4-00-02-3D Example 1439 = X71! =IPL T PCS4 SIS Programming and Control Alarm Relay Functions Command and Response Table for SIS CommandsPower Receptacle Scheduling IPL T PCS4 SIS Programming and Controlreceptacles with current ExampleIPL T PCS4 SIS Programming and Control W X4% %2C X7 %2C X4& SMExample Password and Security SettingsExample Number of connectionsChange or create a directory Directory CommandsIPL T PCS4 SIS Programming and Control Example W LFIPL T PCS4 SIS Programming and Control Reference Material SpecificationsSpecifications Part Numbers and Accessories Ethernet control interface3.5 mm captive screw connector, 2 pole Alarm relay controlGeneral Temperature/humidityOptional Accessories Part Numbers and AccessoriesOptional Accessories Mounting the IPL T PCS4 InterfaceRack mounting procedure Figure 37. Mounting the IPL T PCS4 on a Rack ShelfUnder-desk Mounting Figure 38. Mounting the IPL T PCS4 under FurnitureGlossary Page See Reference threshold See Subnetwork See Reference thresholdand Central America USA, Canada, South AmericaJapan Europe, Africa, and the Middle