Extron electronic IPL T PCS4i manual

Mode 3

Activation	Hold the Reset button in until the Power LED blinks once
	(approximately 3 seconds). Release it, then immediately press it
	again momentarily (for less than 1 second).
	NOTE: Nothing happens if the momentary press does not
	occur within 1 second.
Result	Turns events on or off, depending on their current state. During
	resetting, the reset LED flashes two times if events are starting and
	three times if events are stopping.
Purpose and notes This mode is used for troubleshooting.

Mode 4

Activation	Hold the Reset button in until the Power LED blinks twice
	(approximately 6 seconds). Release it, then immediately press it
	again momentarily (for less than 1 second). The Power LED blinks
	four times in quick succession, confirming a mode 4 reset.
	NOTE: Nothing happens if the momentary press does not
	occur within 1 second.
Result	Reset mode 4 does the following:

•Enables ARP program capability.

•Sets the IP address back to factory IP settings.

•Sets the subnet mask back to factory default.

•Sets the gateway address back to factory default.

•Sets port mapping back to factory default.

•Turns DHCP off.

•Turns events off.

Purpose and notes Mode 4 enables you to set IP address information using ARP and the MAC address.

Mode 5

Activation	Hold in the Reset button until the Power LED blinks three times
	(approximately 9 seconds). Release it, then immediately press it
	again momentarily (for less than 1 second). The power LED blinks
	four times in quick succession, confirming a mode 5 reset.
	NOTE: Nothing happens if the momentary press does not occur
	within 1 second.
Result	Performs a complete reset to factory defaults (except for the
	firmware).
Purpose and notes Mode 5 is useful if you want to start over with control software
	configuration and to replace events.

IPL T PCS4 • Front Panel Features and Operation 14

Image 20

Extron electronic IPL T PCS4i manual Hold the Reset button in until the Power LED blinks once

Contents

IPL T PCS4 IPL T PCS4i Safety Instructions English FCC Class a Notice Notifications Software CommandsConventions Used in this Guide Contents IPL T PCS4 Contents Features IntroductionAbout this Guide About the IPL T PCS4 Application Diagrams IPL T PCS4 Connection Diagram for IPL T PCS4i Installation Rear Panels Installation Overview Rear Panels IPL T PCS4i Rear Panel 220 VAC Setting Up the LAN Port Connecting the DevicesConfiguring the LAN Port LAN Port Cabling IPL T PCS4 Installation and Rear Panel Front Panel Features Operation Front Panel Features Setting Power Level Reference Thresholds Setting Up the System Using the Front PanelSetting Up Power Control Setting the Full power threshold Standby If the receptacle Is set to Power level Receptacle FullNone and Not Set thresholds Front panel Security Lockout Executive Mode LED lit Group Red power LED lit GroupGrouping Receptacles Clearing thresholds Resetting the Unit ModeActivation Result Hold the Reset button in until the Power LED blinks once Setting Up the Computer Using ARP Configuration ControlConfiguring the Hardware ARP-S Command Screen Setting Up the Computer Using a Web Browser Screen Showing the Ping Command Setting up the computer for IP communication Subnet mask Default gateway Blank or Configuring the IPL T PCS4 using a web browser Example of a Default System Settings Using the Embedded Web Pages Password Prompt Window Viewing the System Status System Status Web IP settings ConfigurationSpecifying system settings Date and time settings Removing passwords Assigning passwordsTo assign passwords Entering e-mail addresses for alerts Mail Alerts Screen Upper Portion Upgrading firmware Managing receptacles Switching power to receptacles on and off Grouping receptacles Monitoring the receptacles and setting the alarm Monitoring Settings section Alarm Relay Settings section Scheduling power to receptacles Scheduling an individual receptacle Scheduling receptacles by day of the week All receptacles on and off One receptacle, power on or off File Management Other file management functions Uploading files to the webAdding a directory Query Strings Custom Web PagesServer Side Includes SSIs Example of a Query String Command Code example URL Encoding Browser View of Previous Html Source Code Characters Hex Dec Reserved charactersUnsafe characters Custom Web Pages Device Power ControlAccessing and Using Telnet Port Troubleshooting Power Connections Successful Ping Command Response Network Connections Downloading Global Configurator Software Messages Initiated by the IPL T PCS4 SIS Programming ControlHost-to-Interface Communication Error Response References Password InformationError Responses Using the Command and Response Table Telnet Web Browser Symbol Definitions Example X5@ X71 Command and Response Table for SIS Commands Power Receptacle Monitoring and Alarm Functions Web Browser-specific Commands Password and Security Settings Set GMT offset24 View GMT offset Directory Commands Below Telnet text responses Specifications Reference MaterialEthernet control interface AC control interface Alarm relay control General Part Numbers and Accessories Mounting the IPL T PCS4 Interface Rack mounting procedure Mounting the IPL T PCS4 on a Rack Shelf Under-desk Mounting Mounting the IPL T PCS4 under Furniture Glossary 10/100Base-T Driver Power level reference threshold Subnet USA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe