Manuals / Extron electronic / Computer Equipment / Network Card

Extron electronic IPL T PCS4i manual Configuration, Specifying system settings, IP settings

Models: IPL T PCS4 IPL T PCS4i

1 69

Download 69 pages 31.92 Kb

Page 29

Configuration

Configuration

There are seven Configuration web pages, which only administrators can access. They are listed in the side-bar menu at the left of the Configuration screen. The following sections discuss the tasks that you can perform on these screens.

Specifying system settings

On the System Settings screen, you can set the date and time, and change the IP address information for the PCS4. To change the available system settings:

Figure 14. System Settings Screen on the Configuration Tab

1.On the Configuration page, select System Settings from the side-bar menu at the left edge of the screen. The System Settings screen appears, displaying either the factory default information for your PCS4, or the settings submitted most recently.

2.Enter your new information in the IP Settings section or select the date and time from the menus in the Date/Time Settings section.

IP settings

The following settings are available in the IP Settings section:

•Unit Name: The default is the product name followed by the last six digits of the MAC address. You can give the unit a new name (such as LightsOn&Off or BoardroomA-PCS4) consisting of up to 24 alphanumeric characters including the hyphen (-).

NOTE: The first character must be an alpha character, and the last character cannot be a hyphen. The unit name is not case-sensitive.

•DHCP: DHCP is a communications protocol that assigns addresses on the local network automatically. Select the On or Off radio button to enable or disable DHCP.

•IP Address: You can enter a new network address consisting of four sets of up to three digits, separated by periods (nnn.nnn.nnn.nnn).

•Gateway IP Address: A gateway is a device that connects your network with others that may be using different, incompatible communications protocols. You can enter your gateway address (obtained from your network administrator), using the same format that is used for the IP Address. (If there is no gateway, this field defaults to 0.0.0.0.)

IPL T PCS4 • HTML Configuration and Control 23

Image 29

Extron electronic IPL T PCS4 Specifying system settings, System Settings Screen on the Configuration Tab, IP settings

Contents

IP Link Power Control Interfaces IPL T PCS4 IPL T PCS4iUser Guide IP LinkConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolFCC Class A Notice Conventions Used in this Guide Software CommandsNotifications CopyrightIPL T PCS4 Contents ContentsFront Panel Features and Operation HTML Configuration and ControlIPL T PCS4 Contents About this Guide About the IPL T PCS4 Features Application Diagrams FeaturesIntroduction About this GuideApplication Diagrams Power Control with Sensing Capabilities Figure 2. Connection Diagram for IPL T PCS4iAlarm Codec Camera Monitor Projector IPL T PCS4 IntroductionInstallation Overview Installation and Rear PanelsInstallation Overview Rear Panels Setting Up the LAN Port Connecting the DevicesFigure 5. IPL T PCS4i Rear Panel 220 VAC Rear PanelsConnecting the Devices Setting Up the LAN PortConfiguring the LAN Port RJ-45 ConnectorPage Front Panel Features Front Panel Features and OperationFront Panel Features Setting Up the System Using the Front Panel Resetting the UnitSetting Power Level Reference Thresholds Setting Up the System Using the Front PanelSetting Up Power Control Setting the Full power threshold None and Not Set thresholds And the power levelIf the receptacle is set to The receptacleS LED lit - Group F LED lit - Group Red power LED lit - Group Front panel Security Lockout Executive ModeGrouping Receptacles Clearing thresholdsFigure 8. Reset Button Resetting the UnitMode ActivationMode ModeMode ActivationConfiguring the Hardware HTML Configuration and ControlSetting Up the Computer Using ARP Configuring the Hardware Using the Embedded Web PagesFigure 9. ARP-S Command Screen Figure 10. Screen Showing the Ping Command Setting Up the Computer Using a Web BrowserIPL T PCS4 LAN port defaults PCS4 IP address Gateway IP address Subnet mask DHCP Off Link speed and duplex level Auto detectedSetting up the computer for IP communication Subnet mask Default gateway Blank or Figure 11. Example of a Default System Settings Page Configuring the IPL T PCS4 using a web browserFigure 12. Password Prompt Window Using the Embedded Web PagesFigure 13. System Status Web Page Viewing the System StatusSpecifying system settings ConfigurationFigure 14. System Settings Screen on the Configuration Tab IP settingsDate and time settings Removing passwords Assigning passwordsTo assign passwords Figure 16. E-mail Alerts Screen Upper Portion Entering e-mail addresses for alertsManaging receptacles Figure 17. Firmware Upgrade ScreenUpgrading firmware Grouping receptacles Figure 18. Switching/Grouping ScreenSwitching power to receptacles on and off Figure 19. Monitor Screen Monitoring the receptacles and setting the alarmMonitoring Settings section Alarm Relay Settings section Scheduling an individual receptacle Scheduling power to receptaclesAll receptacles on and off Scheduling receptacles by day of the weekFigure 23. File Management Screen with Two Files Uploaded One receptacle, power on or offFile Management Other file management functions Uploading files to the web pageAdding a directory Custom Web Pages Figure 24. Example of SSI CommandServer Side Includes SSIs #echo var=Figure 25. Example of a Query String Command URL with a Query String Using an SIS CommandCode example Figure 26. Web Page HTML Source Code Document Showing SSIsFigure 29. Characters that Do Not Require Encoding URL EncodingFigure 28. Browser View of Previous HTML Source Code Unsafe characters Reserved charactersCharacters Figure 30. Reserved CharactersAccessing and Using Telnet Port A/V Device Power ControlFigure 32. Telnet Command Prompt Custom Web PagesFigure 33. Connecting to the IP Address TroubleshootingPower Connections Network Connections Figure 34. Successful Ping Command ResponseFigure 35. Response to an Unsuccessful Ping Command Downloading Global Configurator Software Symbol Definitions Command and Response Table for SIS Commands Host-to-Interface Communication Using the Command and Response TableSIS Programming and Control Host-to-Interface CommunicationError Response References Password InformationError Responses Figure 36. ASCII to Hex Conversion Table Using the Command and Response TableTelnet Web BrowserExample Symbol Definitionsfor example IPL-T-PCS4-00-02-3D IPL T PCS4 SIS Programming and Control X71! =Example 1439 = Power Receptacle Scheduling Command and Response Table for SIS CommandsAlarm Relay Functions IPL T PCS4 SIS Programming and ControlIPL T PCS4 SIS Programming and Control Examplereceptacles with current W X4% %2C X7 %2C X4& SMExample Password and Security SettingsExample Number of connectionsIPL T PCS4 SIS Programming and Control Directory CommandsChange or create a directory IPL T PCS4 SIS Programming and Control W LFExample Specifications Part Numbers and Accessories SpecificationsReference Material Ethernet control interfaceGeneral Alarm relay control3.5 mm captive screw connector, 2 pole Temperature/humidityOptional Accessories Part Numbers and AccessoriesOptional Accessories Mounting the IPL T PCS4 InterfaceFigure 37. Mounting the IPL T PCS4 on a Rack Shelf Rack mounting procedureFigure 38. Mounting the IPL T PCS4 under Furniture Under-desk MountingGlossary Page See Reference threshold See Reference threshold See SubnetworkJapan USA, Canada, South Americaand Central America Europe, Africa, and the Middle