Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic MVX PLUS 128 manual Audio input, Audio output, Control/remote - switcher

Models: MVX PLUS 128

1 148

Download 148 pages 51.92 Kb

Page 139

Audio

Routing	12 x 8 stereo matrix
Gain	Unbalanced output: -6 dB; balanced output 0 dB
Frequency response	20 Hz to 20 kHz, ±0.05 dB
THD + Noise	0.03% @ 1 kHz at nominal level
S/N	>90 dB, balanced, at maximum output (21 dBu), unweighted
Crosstalk	<-80 dB @ 1 kHz, fully loaded
Stereo channel separation	>80 dB @ 1 kHz
CMRR	>75 dB @ 20 Hz to 20 kHz

Audio input

Number/signal type	12 stereo, balanced/unbalanced
Connectors	(12) 3.5 mm captive screw connectors, 5 pole
Impedance	>10k ohm, balanced/unbalanced, DC coupled
Nominal level	0 dBV (316 mV) 0 dBu (775 mV)
Maximum level	+19.5 dBu, (balanced or unbalanced) at 0.01% THD+N
Input gain adjustment	-18 dB to +24 dB, adjustable per input by RS-232/422, Ethernet, or front
	panel

N0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu

Audio output

Number/signal type	8 stereo, balanced/unbalanced
Connectors	(8) 3.5 mm captive screw connectors, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±0.1 dB channel to channel
Maximum level (Hi-Z)	>+21 dBu, balanced or unbalanced at 0.10%THD+N
Maximum level (600 ohm)	>+15 dBm, balanced or unbalanced at 0.10%THD+N
Output volume range	0 to 64 (-98 dB to 0 dB) in 1 dB increments from steps 1 to 64, 35 dB
	increment from step 0 to 1

Control/remote — switcher

Serial control port	1 RS-232 or RS-422, 9-pin female D connector
Baud rate and protocol	9600 (default), 19200, 38400, 115200 baud (adjustable); 8 data bits, 1 stop bit,
	no parity
Serial control pin conﬁgurations. RS-232: 2		= TX, 3 = RX, 5 = GND
	RS-422: 2	= TX-, 3 = RX-, 5 = GND, 7 = RX+, 8 = Tx+
Ethernet control port	1 RJ-45 female connector
Ethernet data rate	10/100Base-T, half/full duplex with autodetect
Ethernet protocol	ARP, DHCP, ICMP (ping), TCP/IP, Telnet, HTTP
Program control	Extron’s control/conﬁguration program for Windows®
	Extron’s Simple Instruction Set (SIS™)
	Microsoft® Internet Explorer, Telnet

MVX Plus 128 VGA Matrix Switchers • Speciﬁcations, Part Numbers, Accessories B-3

Image 139

Extron electronic MVX PLUS 128 manual Audio input, Audio output, Control/remote - switcher

Contents

MVX Plus VGA Matrix Switchers68-521-30 Rev. A Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisFront Panel Controls Quick Start - MVX Plus 128 VGA Matrix SwitchersInstallation DeﬁnitionsQS-2 MVX Plus 128 VGA Matrix Switchers Quick Start Quick Start MVX Plus 128 VGA Matrix Switchers, continuedSaing or recalling a preset Viewing and adjusting the audio levelMVX Plus 128 VGA Matrix Switchers Table of Contents Table of Contentsii MVX Plus 128 VGA Matrix Switchers Table of Contents Table of Contents, cont’dMVX Plus 128 VGA Matrix Switchers Table of Contents iv MVX Plus 128 VGA Matrix Switchers Table of Contents Table of Contents, cont’dMVX Plus 128 VGA Matrix Switchers Table of Contents Appendix B Speciﬁcations, Part Numbers, Accessoriesvi MVX Plus 128 VGA Matrix Switchers Table of Contents Table of Contents, cont’d68-521-30 A Introduction MVX Plus 128 VGA Matrix SwitchersAbout this Manual About the Matrix Switchers Deﬁnitions Features Chapter1OneFigure 1-1 - Typical MVX Plus 128 A matrix switcher application InstallationAbout the Matrix Switchers About this ManualMVX Plus 128 VGA Matrix Switchers Introduction DeﬁnitionsConﬁguration - One or more ties or one or more sets of ties Input # FeaturesIntroduction, cont’d 1-4 MVX Plus 128 VGA Matrix Switchers IntroductionTie any input to any or all outputs MVX Plus 128 VGA Matrix Switchers IntroductionIntroduction, cont’d 1-6 MVX Plus 128 VGA Matrix Switchers IntroductionMVX Plus 128 VGA Matrix Switchers InstallationMounting the Switcher Cabling and Rear Panel Views Chapter2TwoInstallation Mounting the SwitcherCabling and Rear Panel Views Video connectionsMVX Plus 128 VGA Matrix Switchers Installation Audio connectionsFigure 2-2 - Captive screw connector wiring for audio inputs Figure 2-3 - Typical audio connectorsFigure 2-5 - RS-232/RS-422 connector Installation, cont’dRS-232/RS-422 connection Figure 2-4 - Captive screw connector wiring for audio outputCabling and RJ-45 connector wiring Ethernet connectionMVX Plus 128 VGA Matrix Switchers Installation Figure 2-6 - RJ-45 connector and pinout tables Reset buttonPower connection Installation, cont’dOperation Front Panel Controls and Indicators Front Panel OperationsRear Panel Controls Optimizing the Audio Troubleshooting Chapter3Three3-2 MVX Plus 128 VGA Matrix Switchers Operation Front Panel Controls and IndicatorsOperation DeﬁnitionsControl buttons Input and output buttonsMVX Plus 128 VGA Matrix Switchers Operation 3-4 MVX Plus 128 VGA Matrix Switchers Operation Operation, cont’dMVX Plus 128 VGA Matrix Switchers Operation I/O controlsFigure 3-2 - Sample button icons Button icons3-6 MVX Plus 128 VGA Matrix Switchers Operation Operation, cont’dMVX Plus 128 VGA Matrix Switchers Operation PowerFront Panel Operations Creating a conﬁgurationFigure 3-3 - Clear all selections 3-8 MVX Plus 128 VGA Matrix Switchers OperationOperation, cont’d Example 1 Creating a set of video and audio tiesInput 5 video/audio tied to outputs 3, 4, and MVX Plus 128 VGA Matrix Switchers OperationFigure 3-6 - Select the outputs Figure 3-7 - Press the Enter buttonFigure 3-9 - Clear all selections 3-10 MVX Plus 128 VGA Matrix Switchers OperationOperation, cont’d Example 2 Adding a tie to a set of video and audio tiesto outputs 3, 4, and MVX Plus 128 VGA Matrix Switchers OperationFigure 3-13 - Press the Enter button Input 5 video tied to outputs 1, 3, 4, and Input 5 audio tiedFigure 3-15 - Clear all selections 3-12 MVX Plus 128 VGA Matrix Switchers OperationOperation, cont’d Example 3 Removing a tie from a set of video and audio tiesVideo Figure 3-20 - Example 3, ﬁnal conﬁguration, audio switcherMVX Plus 128 VGA Matrix Switchers Operation Figure 3-19 - Press the Enter button3-14 MVX Plus 128 VGA Matrix Switchers Operation Viewing a conﬁgurationOperation, cont’d Example 4 Viewing video and audio, audio only, and video only ties MVX Plus 128 VGA Matrix Switchers OperationThe button lights red when selected The button lights green when selectedFigure 3-24 - Deselect RGBHV to view audio ties only Figure 3-26 - Press the View button to exit View-Only mode3-16 MVX Plus 128 VGA Matrix Switchers Operation Operation, cont’dMVX Plus 128 VGA Matrix Switchers Operation I/O groupingFigure 3-27 - I/O grouping of incompatible video formats Operation, cont’d 3-18 MVX Plus 128 VGA Matrix Switchers OperationFigure 3-28 - Clear all selections Figure 3-29 - Select I/O Group modeMVX Plus 128 VGA Matrix Switchers Operation Example 5 Grouping inputs and outputsFigure 3-33 - Assign inputs and outputs 3-20 MVX Plus 128 VGA Matrix Switchers OperationOperation, cont’d Figure 3-32 - Select an I/O groupFigure 3-34 - Clear all selections Setting RGB delayExample 6 Setting the RGB delay for an output MVX Plus 128 VGA Matrix Switchers Operation3-22 MVX Plus 128 VGA Matrix Switchers Operation 9 10Figure 3-35 - Select RGB Delay mode Figure 3-37 - Adjust the RGB delay intervalMVX Plus 128 VGA Matrix Switchers Operation Using presetsFigure 3-38 - Deselect RGB Delay mode Figure 3-39 - Preset locations3-24 MVX Plus 128 VGA Matrix Switchers Operation Example 7 Saving a presetFigure 3-41 - Enter Save Preset mode Figure 3-42 - Select the presetMVX Plus 128 VGA Matrix Switchers Operation Example 8 Recalling a presetFigure 3-45 - Enter Recall Preset mode Figure 3-46 - Select the presetFigure 3-47 - Press the Enter button Muting and unmuting video and/or audio outputs3-26 MVX Plus 128 VGA Matrix Switchers Operation Operation, cont’dFigure 3-49 - Select RGBHV and audio MVX Plus 128 VGA Matrix Switchers OperationExample 9 Muting and unmuting an output Figure 3-48 - Clear all selectionsFigure 3-51 - Unmute the outputs 3-28 MVX Plus 128 VGA Matrix Switchers OperationOperation, cont’d Figure 3-50 - Mute the outputsFigure 3-53 - Audio gain and attenuation Viewing and adjusting the input audio levelFigure 3-52 - Press the View button to exit View-Only mode MVX Plus 128 VGA Matrix Switchers OperationOperation, cont’d Example 10 Viewing and adjusting an input audio levelFigure 3-55 - Select Audio mode 3-30 MVX Plus 128 VGA Matrix Switchers OperationMVX Plus 128 VGA Matrix Switchers Operation Input audio level adjustment displaysIndications 1 2 3 F 4 Figure 3-57 - Adjust the input audio level3-32 MVX Plus 128 VGA Matrix Switchers Operation Operation, cont’dFigure 3-58 - Deselect Audio mode Viewing and adjusting the output volumeMVX Plus 128 VGA Matrix Switchers Operation 3-34 MVX Plus 128 VGA Matrix Switchers Operation Reading the displayed volumeOperation, cont’d MVX Plus 128 VGA Matrix Switchers Operation Audio volume adjustment settingsattenuation Operation, cont’d Example 11 Viewing and adjusting an output volume levelFigure 3-60 - Select Audio mode 3-36 MVX Plus 128 VGA Matrix Switchers Operation1 2 3 4 5 6 7 F 8 9 10 11 Figure 3-62 - Adjust the output audio volumeFigure 3-63 - Deselect Audio mode MVX Plus 128 VGA Matrix Switchers Operation3-38 MVX Plus 128 VGA Matrix Switchers Operation Locking out the front panel Executive modePerforming a system reset from the front panel Figure 3-65 - System resetMVX Plus 128 VGA Matrix Switchers Operation Background illuminationFigure 3-66 - Toggle background illumination on or off Operation, cont’d Selecting the RS-232/RS-422 protocol and baud rateFigure 3-69 - Exit Serial Port Conﬁguration mode 3-40 MVX Plus 128 VGA Matrix Switchers OperationRear Panel Controls Performing soft system resetsMVX Plus 128 VGA Matrix Switchers Operation 3-42 MVX Plus 128 VGA Matrix Switchers Operation Figure 3-70 - Whole switcher and absolute resetsOperation, cont’d MVX Plus 128 VGA Matrix Switchers Operation Performing a hard resetOptimizing the Audio Figure 3-71 - Hard reset3-44 MVX Plus 128 VGA Matrix Switchers Operation TroubleshootingConﬁguration Worksheets Worksheet example 1 System equipmentMVX Plus 128 VGA Matrix Switchers Operation Worksheet example 2 Daily conﬁgurationFigure 3-73 - Worksheet example 2 Daily conﬁguration Figure 3-74 - Worksheet example 3 Test conﬁguration Worksheet example 3 Test conﬁguration3-46 MVX Plus 128 VGA Matrix Switchers Operation Operation, cont’dInput sources Conﬁguration worksheetPreset # Switchers OperationOperation, cont’d 3-48 MVX Plus 128 VGA Matrix Switchers OperationCommand/Response Table for SIS Commands RS-232/RS-422 Link Ethernet Link Host-to-Switcher InstructionsSwitcher-Initiated Messages Switcher Error Responses Using the Command/Response Tables4-2 MVX Plus 128 VGA Matrix Switchers Programmer’s Guide SIS Programming and ControlRS-232/RS-422 Link Figure 4-1 - Remote connector pin assignmentsMVX Plus 128 VGA Matrix Switchers Programmer’s Guide Default IP addressesEthernet Link Figure 4-2 - RJ-45 Ethernet connector pin assignments4-4 MVX Plus 128 VGA Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages SIS Programming and Control, cont’dUsing the Command/Response Tables Switcher Error ResponsesMVX Plus 128 VGA Matrix Switchers Programmer’s Guide Symbol deﬁnitions Command/Response Table for SIS CommandsSIS Programming and Control, cont’d Create ties Command/response table for SIS commandsRead ties Audio output volume Command/response table for SIS commands continuedVideo mute commands RGB delayMVX Plus 128 VGA Matrix Switchers Programmer’s Guide Audio volume adjustment settingsSIS Programming and Control, cont’d EX11X12...X112OX11X12X13...X112 Command/response table for SIS commands continuedSave, recall, and directly write presets Command/response table for SIS commands continuedE +X1! PX@ *X# !X@ *X# %X@ *X# $ ... X@ *X# Resets Command/response table for SIS commands continuedSave, recall, and directly write presets continued Executive modeView ties, gain, volume, mutes, presets, and DSVP Command/response table for SIS commands continuedCommand description Response description 4-14 MVX Plus 128 VGA Matrix Switchers Programmer’s Guide Command/response table for SIS commands continuedCommand ASCII commandMVX Plus 128 VGA Matrix Switchers Programmer’s Guide Command/response table for SIS commands continuedCommand ASCII commandSIS Programming and Control, cont’d Command/Response Table for IP SIS CommandsSymbol deﬁnitions 4-16 MVX Plus 128 VGA Matrix Switchers Programmer’s GuideEX4! CR Command/response table for IP SIS commandsSIS Programming and Control, cont’d Special CharactersMVX Plus 128 VGA Matrix Switchers Matrix Switchers Control Program Button Label Generator ProgramChapter5Five Matrix SoftwareSoftware operation via Ethernet Matrix Switchers Control ProgramInstalling the software Matrix SoftwareMVX Plus 128 VGA Matrix Switchers Matrix Software Using the softwareFigure 5-1 - Comm port selection window If the IP address is correct Proceed to step 3b Matrix Software, cont’dFigure 5-2 - Address and password entry 5-4 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareMVX Plus 128 VGA Matrix Switchers Matrix Software Figure 5-3 - Extron Matrix Switcher+ Control Program window blankFigure 5-4 - Sample program window complete Matrix Software, cont’d IP Settings/Options windowFigure 5-5 - Control program IP setting/options window 5-6 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareExtron Name/Descriptor ﬁeld N Editing the Extron IP address while connected via the Ethernet port can immediately disconnect the user from the matrix switcher. Extron recommends editing this ﬁeld using the RS-232/RS-422 link and protecting the Ethernet access to this screen by assigning an administrator’s password to qualiﬁed and knowledgeable personnel onlyMVX Plus 128 VGA Matrix Switchers Matrix Software Matrix IP Address ﬁeldSubnet Mask ﬁeld 5-8 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareMatrix Software, cont’d Gateway IP address ﬁeldGMT offset ﬁeld MVX Plus 128 VGA Matrix Switchers Matrix SoftwareTime local ﬁeld Sync Time to PC buttonMatrix Software, cont’d Administrator Password ﬁeldUser Password ﬁeld 5-10 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareMail Server Domain Name ﬁeld Mail Server Password ﬁeldMVX Plus 128 VGA Matrix Switchers Matrix Software Mail Server IP Address ﬁeldE-mail Addressee ﬁelds 5-12 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareMatrix Software, cont’d Miles StandishMVX Plus 128 VGA Matrix Switchers Matrix Software Updating ﬁrmwareFigure 5-7 - Open ﬁle window Figure 5-8 - HTML Files List window Uploading HTML ﬁles5-14 MVX Plus 128 VGA Matrix Switchers Matrix Software Matrix Software, cont’dFile menu Windows buttons, drop boxes, and trashcanWindows menus MVX Plus 128 VGA Matrix Switchers Matrix SoftwareFigure 5-9 - Status window 5-16 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareMatrix Software, cont’d Tools menuPreferences menu MVX Plus 128 VGA Matrix Switchers Matrix SoftwareFigure 5-10 - Ties shown as lines set this option to Automatically every 10 seconds 5-18 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareMatrix Software, cont’d Figure 5-11 - Ties shown as crosspointsMVX Plus 128 VGA Matrix Switchers Matrix Software Using emulation modeUsing the help system Master-Reset selectionMatrix Software, cont’d Button-Label Generator ProgramUsing the software 5-20 MVX Plus 128 VGA Matrix Switchers Matrix SoftwareFile Management Page Set and View Ties Page Special Characters Chapter66HTML Operation Download the Startup Page System Status Page System Conﬁguration Page6-2 MVX Plus 128 VGA Matrix Switchers HTML Operation HTML OperationDownload the Startup Page Figure 6-1 - Enter Network Password pageMVX Plus 128 VGA Matrix Switchers HTML Operation System Status PageFigure 6-2 - System Status page Figure 6-3 - DSVP page HTML Operation, cont’dDSVP page 6-4 MVX Plus 128 VGA Matrix Switchers HTML OperationMVX Plus 128 VGA Matrix Switchers HTML Operation System Conﬁguration PageFigure 6-4 - System Conﬁguration page Unit Name ﬁeld IP Settings ﬁelds6-6 MVX Plus 128 VGA Matrix Switchers HTML Operation HTML Operation, cont’dFigure 6-5 - Date/Time Settings ﬁelds Date/Time Settings ﬁeldsMVX Plus 128 VGA Matrix Switchers HTML Operation HTML Operation, cont’d Passwords pageFigure 6-6 - Passwords page 6-8 MVX Plus 128 VGA Matrix Switchers HTML OperationMail IP Address ﬁeld Email Settings pageFigure 6-7 - Email Settings page MVX Plus 128 VGA Matrix Switchers HTML OperationHTML Operation, cont’d Firmware Upgrade pageFigure 6-8 - Firmware Upgrade page 6-10 MVX Plus 128 VGA Matrix Switchers HTML OperationMVX Plus 128 VGA Matrix Switchers HTML Operation File Management PageFigure 6-9 - File Management page Figure 6-10 - Set and View Ties page Set and View Ties Page6-12 MVX Plus 128 VGA Matrix Switchers HTML Operation HTML Operation, cont’dMVX Plus 128 VGA Matrix Switchers HTML Operation RGB and Audio Settings pageCreating a tie Figure 6-11 - RGB and Audio Settings pageFigure 6-12 - Input selection drop box 6-14 MVX Plus 128 VGA Matrix Switchers HTML OperationHTML Operation, cont’d Changing the input gain and attenuationFigure 6-15 - Mute status indications MVX Plus 128 VGA Matrix Switchers HTML OperationMuting and unmuting one or all outputs Figure 6-14 - Output selection drop boxHTML Operation, cont’d Changing the RGB delayFigure 6-17 - RGB delay drop box 6-16 MVX Plus 128 VGA Matrix Switchers HTML OperationFigure 6-18 - Output selection drop box Changing the output volume levelFigure 6-19 - Volume drop box MVX Plus 128 VGA Matrix Switchers HTML Operation6-18 MVX Plus 128 VGA Matrix Switchers HTML Operation Audio volume adjustment settingsHTML Operation, cont’d Recalling a preset Global Presets pageFigure 6-20 - Global Presets page Saving a presetHTML Operation, cont’d 6-20 MVX Plus 128 VGA Matrix Switchers HTML OperationSpecial Characters MVX Plus 128 VGA Matrix Switchers AAppendix AEthernet Connection Ethernet Link Subnetting - A PrimerA-2 MVX Plus 128 VGA Matrix Switchers Ethernet Connection Default addressEthernet Connection Figure A-1 - RJ-45 connector pinout tablesPinging to determine Web IP address MVX Plus 128 VGA Matrix Switchers Ethernet Connection A-3Pinging to determine Extron IP address Figure A-2 - Ping responseFigure A-3 - Telnet screen Connecting as a Telnet clientEthernet Connection, cont’d A-4 MVX Plus 128 VGA Matrix Switchers Ethernet ConnectionSet carriage return-line feed MVX Plus 128 VGA Matrix Switchers Ethernet Connection A-5Escape character and Esc key Local echoIP addresses and octets Subnetting - A PrimerGateways Local and remote devicesMasked octets are not compared indicated by X in ﬁgure A-6 Determining whether devices are on the same subnetMVX Plus 128 VGA Matrix Switchers Ethernet Connection A-7 Unmasked octets are compared indicated by ? in ﬁgure A-6Ethernet Connection, cont’d A-8 MVX Plus 128 VGA Matrix Switchers Ethernet ConnectionMVX Plus 128 VGA Matrix Switchers Speciﬁcations, Part Numbers, AccessoriesSpeciﬁcations Part Numbers and Accessories Button Labels AppendixBBVideo input Speciﬁcations, Part Numbers, AccessoriesSpeciﬁcations VideoAudio output Control/remote - switcherAudio Audio inputGeneral Speciﬁcations, Part Numbers, Accessories, cont’dReplacement part Part Numbers and AccessoriesAccessories Included partsMale-to-female VGA backshell connector cables CablesSpeciﬁcations, Part Numbers, Accessories, cont’d Male-to-female VGA molded connector cablesButton Labels Installing labels in the matrix switcher’s buttonsSpeciﬁcations, Part Numbers, Accessories, cont’d Button label blanks Speciﬁcations, Part Numbers, Accessories, cont’d Europe, Africa, and the Middle East Extron’s WarrantyFCC Class A Notice USA, Canada, South AmericaExtron Electronics, Japan Extron Electronics, USAExtron Electronics, Europe Extron Electronics, Asia