Remote Control of the System 7SC | Extron electronic specification

MODE

DISPLAY

POWER MUTE

MAX/

MIN

AUDIO VOLUME

SHOW ME

Extron

System 7SC

Press for

2 seconds

COLOR DETAIL

Hold for 2s for

Executive Mode

Release Keys

Executive Mode

On

4sec. timeout

Extron

System 7SC

Press for

2 seconds

COLOR DETAIL

Hold for 2s for

Executive Mode

Release Keys

Executive Mode

Off

4sec. timeout

Enabling and disabling executive mode

Remote Control of the System 7SC

The System 7SC can be controlled by using its front panel controls; an optional IR 701 infrared remote control; optional SCP/AAP A, SCP 200, and/or SCP 250 remote control pads; or an RS-232 control device or computer.

SCP control pads

The Extron SCP/AAP A control pad replicates a few of the front panel controls. It provides Display Power, Display Mute, and Display Mode buttons, and a

Show Me button. Pressing the Show Me button selects a specific input, which is determined by setting the DIP

switch on the control pad’s circuit board. Another

control device must be used to select any other input, make adjustments, or configure the switcher.

SCP / AAP A

The SCP 200, shown at left below, replicates the control (Display Power, Display Mute, display Mode, Room 1, Room 2) and input selection buttons. The SCP 200 has an IR receiver device for receiving commands for the System 7SC from the IR 701.

IR

DISPLAY

DISPLAY

MODE

ROOM/

ROOM/

1

POWER

MUTE

RELAY 1

RELAY 2

2

3

4

5

6

7

SCP 200

	DISPLAY			AUDIO
POWER	MUTE	MODE		MAX/
		MODE		MAX/			IR
							IR
				MIN
				VOLUME
ROOM	ROOM	1	2	3	4	5	6	7
1	2	1	2	3	4	5	6	7

SCP 250

The SCP 250, shown at right above, includes all the features of the SCP 200 and adds a volume control knob and LED.

Setup and adjustments cannot be performed from the SCP 200 or SCP 250.

A total of up to sixteen SCP/AAP A, SCP 200, or SCP 250 control pads can be linked together and connected to the System 7SC switcher. See the SCP’s user’s manual for details on how to configure and link SCP control pads.

System 7SC • Operation and Configuration 3-19

Image 47

Extron electronic manual Remote Control of the System 7SC, SCP control pads, Enabling and disabling executive mode

Contents

System 7SC System Switcher Instrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch Table of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One Typical System 7SC application What is the System 7SC?About this Manual About the System 7SC Controlling the switcher and an A/V system MHz -3 dB video bandwidth Configurable video inputs Features and OptionsFeatures Options and accessories Introduction, cont’d Two Rack mounting Mounting the SwitcherCabling and Panel Views Tabletop use System 7SC Front Panel Front panel inputs Power, video, and audio conections Rear panel inputs Outputs Captive screw connector wiring for rear panel audio inputs Audio inputs RGB Control device connections IR communications port IR Comm For the IR Emitter only IR Communications port wiring options UC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC Rear Panel System 7SC master connected to a slaved switcher Labeling Buttons on the System 7SC and SCPs Example of input numbering with a six-input slaved switcher System 7SC button label screen SCP 200 button label screen Installing the softwareUsing the software Button-Label Generator software Installing labels in the System 7SC’s buttons Three System 7SC Operation and Configuration Front Panel Features and Basic OperationControl features Display Mute button Display Power buttonMode button Adjustment features Operation and Configuration, cont’d Display command indicator LEDs Input selection featuresMiscellaneous features Example IR and RS-232 Projector ControlProjector control memory Projector control memory usage Optimizing the System Setting up a DVD source Menu overview Menus, Configuration, and AdjustmentsMoving through menus by using front panel controls Default menus Scaler Polarity +/V+ Switcher Setup/Configuration Scaler Polarity sync polarity Scaler Rate resolution and refresh rateRGB Delay Triple-Action Switching Scaler Sync RGB format Edge Smoothing Add Slave slaving switchersSystem 7SC with a slaved switcher Input Configuration signal format Audio/Video Adjustments Size Input Blank Input blanking adjustmentAudio Level Image Size Navigating through the IR Learning Configuration menu IR Learning Configuration Clearing IR commands from a button’s memory Clearing IR commands from memories Initiating IR learning Initiating IR learning Information/System Options Image adjustmentsReset to Default clearing settings and adjustments Global system reset Centering Executive mode front panel lockoutInput you wish to adjust SCP control pads Remote Control of the System 7SCEnabling and disabling executive mode Selecting an input IR 701 infrared remote control Four RS-232 Programmer’s Guide Host-to-switcher communicationsSwitcher-initiated messages Error responses Ascii to Hex conversion table Using the command/response tablesSymbol definitions Command Ascii Command Response Additional description Tint Video configurationDetail mode Color Top blanking Image sizeHorizontal size Vertical size Firmware version, part number & information requests Executive mode front panel lockoutZap reset to default settings Room relays Command Ascii Command Response ValuesDelay times Scaler settings Miscellaneous settings Audio settingsIR-related settings Send/receive a flag parameter block Command Hex. command Response Additional descriptionSend/receive data to/from page 0 memory Send/receive data to/from page 1 memory Control Software for Windows Installing the softwareUsing the control program Mini Mode Configuration User ModeSpecial features Real Time Adjustments Projector Driver Room & Misc. Options Saving and restoring configurations Key to file names File name Description Using the help programDownloading and using projector drivers AAppendix a System 7SC Reference Material Specifications Sync Reference Material, cont’d Accessories Part number Part Numbers and AccessoriesAccessories Included parts Replacement Part number Align Notches Firmware Upgrade Installation System 7SC Reference Material Glossary Asia Japan FCC Class a Notice Extron’s Warranty Extron Electronics, USA