IR 701 infrared remote control | Extron electronic System 7SC

Operation and Configuration, cont’d

IR 701 infrared remote control

The IR 701, shown at right, replicates all of the front panel controls except the Menu and Next buttons. Unless executive mode is enabled, adjustments can be made from the IR 701, but you must use the System 7’s front panel or the Windows-based control program (via an RS-232 device) to configure and program the switcher. See chapter four, “Serial Communication”, for details.

Control Functions			Audio
Display	Display		Mute
Power	Mute		Mute
	Mode		Volume
	Input Selection
1	2	3	4
5	6	7	8
9	0		ENTER

The topmost part of the IR 701 includes the control functions (Display Power, Mute, Mode) and the master volume control (as ^ and ^ buttons). The middle portion of the IR 701 features the input selection buttons, Room 1, Room 2, and centering/shift buttons. The bottom part contains the adjustment controls for color, tint, brightness, contrast, and detail adjustments. The

Room 1

Room 2

COLOR

SHIFT

Image Adjustments

adjustment functions will be disabled if executive mode is on.

Selecting an input

TINTBRIGHT

CONTDETAIL

IR 701

System Remote

To use the IR 701 to select an input, press the input number, then press the Enter key. For example, if a switcher is slaved to the System 7 and you want to select input 15, press 1, press 5, then press Enter. The System 7 will switch to input 15.

If you select an input that doesn’t exist, such as input 8 when a slave switcher is not connected, the switcher will ignore the command.

3-20 System 7SC • Operation and Configuration

Image 48

Extron electronic System 7SC manual IR 701 infrared remote control, Selecting an input

Contents

System Switcher System 7SC Safety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad Español Table of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One What is the System 7SC? About this ManualAbout the System 7SC Typical System 7SC application Controlling the switcher and an A/V system Features and Options FeaturesMHz -3 dB video bandwidth Configurable video inputs Options and accessories Introduction, cont’d Two Mounting the Switcher Cabling and Panel ViewsTabletop use Rack mounting System 7SC Front Panel Power, video, and audio conections Front panel inputs Rear panel inputs Captive screw connector wiring for rear panel audio inputs Outputs Audio inputs Control device connections RGB IR communications port IR Comm IR Communications port wiring options For the IR Emitter only UC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC master connected to a slaved switcher System 7SC Rear Panel Example of input numbering with a six-input slaved switcher Labeling Buttons on the System 7SC and SCPs Installing the software Using the softwareButton-Label Generator software System 7SC button label screen SCP 200 button label screen Installing labels in the System 7SC’s buttons Three Front Panel Features and Basic Operation Control featuresSystem 7SC Operation and Configuration Display Power button Mode buttonDisplay Mute button Operation and Configuration, cont’d Adjustment features Input selection features Miscellaneous featuresDisplay command indicator LEDs IR and RS-232 Projector Control Projector control memoryProjector control memory usage Example Setting up a DVD source Optimizing the System Menus, Configuration, and Adjustments Moving through menus by using front panel controlsDefault menus Menu overview Switcher Setup/Configuration Scaler Polarity +/V+ Scaler Rate resolution and refresh rate RGB Delay Triple-Action SwitchingScaler Sync RGB format Scaler Polarity sync polarity Add Slave slaving switchers System 7SC with a slaved switcherEdge Smoothing Audio/Video Adjustments Input Configuration signal format Blank Input blanking adjustment Audio LevelImage Size Size Input IR Learning Configuration Navigating through the IR Learning Configuration menu Clearing IR commands from memories Clearing IR commands from a button’s memory Initiating IR learning Initiating IR learning Image adjustments Reset to Default clearing settings and adjustmentsGlobal system reset Information/System Options Executive mode front panel lockout Input you wish to adjustCentering Remote Control of the System 7SC Enabling and disabling executive modeSCP control pads IR 701 infrared remote control Selecting an input Four Host-to-switcher communications Switcher-initiated messagesError responses RS-232 Programmer’s Guide Using the command/response tables Symbol definitionsAscii to Hex conversion table Command Ascii Command Response Additional description Video configuration Detail modeColor Tint Image size Horizontal sizeVertical size Top blanking Executive mode front panel lockout Zap reset to default settingsFirmware version, part number & information requests Command Ascii Command Response Values Delay timesScaler settings Room relays Audio settings IR-related settingsMiscellaneous settings Command Hex. command Response Additional description Send/receive data to/from page 0 memorySend/receive data to/from page 1 memory Send/receive a flag parameter block Installing the software Using the control programMini Mode Control Software for Windows User Mode Special featuresConfiguration Real Time Adjustments Projector Driver Saving and restoring configurations Room & Misc. Options Using the help program Downloading and using projector driversKey to file names File name Description AAppendix a Specifications System 7SC Reference Material Sync Reference Material, cont’d Part Numbers and Accessories AccessoriesIncluded parts Replacement Part number Accessories Part number Firmware Upgrade Installation Align Notches System 7SC Reference Material Glossary FCC Class a Notice Extron’s Warranty Asia Japan Extron Electronics, USA