Part Numbers and Accessories | Extron electronic System 7SC guide

Part Numbers and Accessories

Included parts

These items are included in each order for a System 7SC switcher:

Included parts	Replacement
	part number

System 7SC (1)	60-340-01

Rubber feet (self-adhesive) (4)
Rack mounting kit (brackets and screws) (1)	70-155-01

IR Emitter (1)	70-283-01
Batteries for the IR 701 remote control (2)

9-pin male-to-male adapter (9-pin D GCM) (1)	26-128-01
3.5 mm, 5-pole captive screw connectors (11)	10-319-10

3.5 mm, 10-pole captive screw connectors (2)	10-319-11
UC 50’ (15 m) universal projector control cable	26-518-01

IEC power cord
Tweeker (small screwdriver)

System 7SC User’s Manual
System 7SC Windows-based
control/configuration program

Accessories

These items can be ordered separately:

Accessories	Part number

IR Broadcaster	60-272-01

Current/display power sensor	60-271-01
IR 701 remote control	70-145-01

SCP 200 (gray, black, white)	60-338-01, -02, -03
SCP 250 (gray, black, white)	60-356-01, -02, -03

IR Emitter and shield	70-283-01
Dual IR Emitter and shield	70-283-02

UC 100’ (30 m) universal projector control cable	26-518-02
UC 200’ (61 m) universal projector control cable	26-518-03

System 7SC • Reference Material

A-5

Image 69

Extron electronic System 7SC manual Part Numbers and Accessories, Included parts Replacement Part number

Contents

System 7SC System Switcher Consignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad Español Table of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One About this Manual What is the System 7SC?About the System 7SC Typical System 7SC application Controlling the switcher and an A/V system Features and Options FeaturesMHz -3 dB video bandwidth Configurable video inputs Options and accessories Introduction, cont’d Two Cabling and Panel Views Mounting the SwitcherTabletop use Rack mounting System 7SC Front Panel Front panel inputs Power, video, and audio conections Rear panel inputs Outputs Captive screw connector wiring for rear panel audio inputs Audio inputs RGB Control device connections IR communications port IR Comm For the IR Emitter only IR Communications port wiring options UC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC Rear Panel System 7SC master connected to a slaved switcher Labeling Buttons on the System 7SC and SCPs Example of input numbering with a six-input slaved switcher Using the software Installing the softwareButton-Label Generator software System 7SC button label screen SCP 200 button label screen Installing labels in the System 7SC’s buttons Three Front Panel Features and Basic Operation Control featuresSystem 7SC Operation and Configuration Display Power button Mode buttonDisplay Mute button Adjustment features Operation and Configuration, cont’d Input selection features Miscellaneous featuresDisplay command indicator LEDs Projector control memory IR and RS-232 Projector ControlProjector control memory usage Example Optimizing the System Setting up a DVD source Moving through menus by using front panel controls Menus, Configuration, and AdjustmentsDefault menus Menu overview Scaler Polarity +/V+ Switcher Setup/Configuration RGB Delay Triple-Action Switching Scaler Rate resolution and refresh rateScaler Sync RGB format Scaler Polarity sync polarity Add Slave slaving switchers System 7SC with a slaved switcherEdge Smoothing Input Configuration signal format Audio/Video Adjustments Audio Level Blank Input blanking adjustmentImage Size Size Input Navigating through the IR Learning Configuration menu IR Learning Configuration Clearing IR commands from a button’s memory Clearing IR commands from memories Initiating IR learning Initiating IR learning Reset to Default clearing settings and adjustments Image adjustmentsGlobal system reset Information/System Options Executive mode front panel lockout Input you wish to adjustCentering Remote Control of the System 7SC Enabling and disabling executive modeSCP control pads Selecting an input IR 701 infrared remote control Four Switcher-initiated messages Host-to-switcher communicationsError responses RS-232 Programmer’s Guide Using the command/response tables Symbol definitionsAscii to Hex conversion table Command Ascii Command Response Additional description Detail mode Video configurationColor Tint Horizontal size Image sizeVertical size Top blanking Executive mode front panel lockout Zap reset to default settingsFirmware version, part number & information requests Delay times Command Ascii Command Response ValuesScaler settings Room relays Audio settings IR-related settingsMiscellaneous settings Send/receive data to/from page 0 memory Command Hex. command Response Additional descriptionSend/receive data to/from page 1 memory Send/receive a flag parameter block Using the control program Installing the softwareMini Mode Control Software for Windows User Mode Special featuresConfiguration Real Time Adjustments Projector Driver Room & Misc. Options Saving and restoring configurations Using the help program Downloading and using projector driversKey to file names File name Description AAppendix a System 7SC Reference Material Specifications Sync Reference Material, cont’d Accessories Part Numbers and AccessoriesIncluded parts Replacement Part number Accessories Part number Align Notches Firmware Upgrade Installation System 7SC Reference Material Glossary Asia Japan FCC Class a Notice Extron’s Warranty Extron Electronics, USA