Installing the HDD module | Fujitsu RX330 specs

Hot plug hard disk drives

Hot-plug components

Installing the HDD module

1

2

Figure 21: Installing the HDD module

ÊUnlock the HDD module as described in section “Unlocking the HDD module” on page 77.

ÊCarefully push the HDD module into the empty mounting location (1) until it stops.

ÊPush the handle completely in the direction of the arrow (2) until the locking mechanism engages.

78

Operating manual

RX330 S1

Image 78

Fujitsu RX330 manual Installing the HDD module

Contents

Primergy RX330 S1 Server Comments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Contents Contents Abbreviations Literature Index Page Introduction Documentation overviewConcept and target groups for this manual Documentation overview Additional server documentation Further sources of information FeaturesIntroduction System board Power supply FeaturesAccessible drives USB port IRMC with integrated service LAN port Features Server management Service and support ServerStart RemoteView Notational conventions Notational conventions Technical data Electrical data hot-plug power supply unitCompliance with regulations and standards Mechanical values Technical dataWeight Ventilation clearance Installation steps, overview Installation steps, overview Safety Important information Safety Installation and operationBefore starting up Important information Safety Working with CDs/DVDs and CD/DVD drives Laser informationNever remove parts of the CD/DVD drive casing Batteries Modules with Electrostatic-Sensitive Devices ESD label CE conformity CE conformityFCC Class a Compliance Statement Other important information Transporting the server Important information Energy-saving information Environmental protectionEnvironmentally-friendly product design and development Packaging information Environmental protection Labels on plastic casing partsReturns, recycling and disposal Hardware installation Minimum acclimatization timeHours Unpacking the server Unpacking the server Installing/removing the server in/from the rack Rack requirements Installing/removing the server in/from the rack Primecenter RackDataCenter Rack Operating manual Mechanical requirements Installation in PRIMECENTER/DataCenter Rack Fitting the support bracket Remove the outer telescopic rail Operating manual Installation in 3rd party racks Racks with installation depth of 735 mm Inserting the server Preparing the server Inserting the server Connecting devices to the server Hardware installation Connecting devices to the server Connecting the keyboard, mouse and monitor Connecting the server to the mains Connecting the server to the mains Connecting cables Disconnecting cables Starting up and operation Controls and displaysFront of server Indicators on the control panel Controls and displaysControls Indicators on the drives CD/DVD indicator Starting up and operation Indicators on the HDD module LED Global error indicator and ID indicator Rear of server Indicators on the connection panel LAN indicators LAN indicators Hot-plug PSU indicators Status Meaning Switching the server on Switching the server on and offSwitching the server on and off System already installed Ring indicator Switching the server OFFSpecified switch on time / switch off time After power failure Configuring the server Configuring onboard SAS controllerConfiguring the server Configuration with ServerStart ServerStart advantages Cleaning the server Cleaning the serverConfiguration without ServerStart Configuring onboard SAS controller Preventing unauthorized system access Bios Setup security functionsPreventing unauthorized Bios Setup calls Property and data protection Protecting Bios from being overwritten Protecting the server from being switched off by a program Power cable incorrectly connected Troubleshooting and tipsPower-on indicator remains unlit Power supply overloaded Server switches itself off Screen remains blank Flickering stripes on monitor screen No screen display or display driftsNo mouse pointer displayed on screen SAS configuration incorrect System will not bootMouse controller disabled Incorrect date and time RAID controller configuration incorrect Drives reported as dead when starting systemError message on screen RAID controller is not configured for this drivePage Hot-plug power supply units Hot-plug components Hot-plug power supply units Remove the dummy module Installing/removing the hot-plug power supply unit Hot-plug components Replacing the hot-plug power supply unit Hot plug hard disk drives Hot plug hard disk drives HDD module and dummy module Handling hard disk drives and HDD modules Removing/Installing the dummy module Removing the dummy module Installing/removing the HDD module Unlocking the HDD module Installing the HDD module Installing the HDD module Removing the HDD module Vcaution Abbreviations Abbreviations IRMC LBA RAM SEL Literature Literature Primergy ServerView Suite ServerView S2 Primergy ServerView Suite ServerViewPrimergy ServerView Suite Index CD-RW DVD-RW Index DVD USB Dimensions Electrical data Index