Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny EEG-141, EEG-142, EEG-144 Program Code Change SP-25 Continued, Usage Code Change SP-26

Models: EEG-143 EEG-144 EEG-141 EEG-142

1 72

Download 72 pages 1.4 Kb

Page 65

Program Code Change (SP-25) (Continued)

6-1. SPECIAL PROGRAM MODE (Continued)

1009

Model EEG-141, 142, 143, 144

Program Code Change (SP-25) (Continued)

If satisfied with code, press and “*CODE CHANGED*” shows in display.

If not satisfied with code, press and “*CANCEL” shows in display, then reverts back to “SP-25” and “CHANGE, MGR CODE? 1=YES”. Now the above steps can be repeated.

Usage Code Change (SP-26)

This allows the operator to change the reset usage code (factory set at 1, 2, 3) to reset the usage amounts of each product. See Review Usage step in Information Mode.

Press button and “SP-26 CHANGE USAGE CODE?

1=YES” flashes in the display. Press and “ENTER NEW CODE, P=DONE, I=QUIT show scrolls through the display. Press the product buttons for new code.

If satisfied with code, press and “REPEAT NEW CODE, P=DONE, I=QUIT, shows in display. Press same code buttons.

If satisfied with code, press “*CODE CHANGED*” shows in display.

If not satisfied with code, press and “*CANCEL” shows in display, then reverts back to “SP-26” and “CHANGE, USAGE CODE? 1=YES”. Now the above steps can be repeated.

Dispose Requires Code ? (SP-27)

Press button and “SP-27 DISPOSE REQUIRES CODE ?” flashes in the left display. Press the or buttons to choose YES or NO. If set to YES, code 1, 2, 3 must be entered to discard the oil from the vat, using the Dispose Mode.

Longer Fill Time (SP-28)

Press button and “SP-28 LONGER FILLTIME ENABLED?” flashes in the left display. Press the or buttons to choose YES or NO.

Let User Exit Fill (SP-29)

Press button and “SP-29 LET USER EXIT FILL”

flashes in the left display. Press the or buttons to choose YES or NO. If YES is chosen, the user can exit the Express FilterTM fill operation.

6-9

Image 65

Henny Penny EEG-141, EEG-142 Program Code Change SP-25 Continued, Usage Code Change SP-26, Dispose Requires Code ? SP-27

Contents

Henny Penny Evolution Elite OPERATOR’S MANUALReduced Oil Capacity Open Fryers Split Vat & Full Vat- Gas Model EEG-141 Model EEG-142 Model EEG-143 Model EEG-144Page FM05-057-C Revised DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORSTechnical Data for CE Marked Products Revised 01/01/07 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENTPage TABLE OF CONTENTSSection Section TABLE OF CONTENTS ContinuedPage Fryer SetupPage SECTION 1. INTRODUCTION 1-2. FEATURES1-1. INTRODUCTION 1-3. PROPER CAREASSISTANCE SAFETYDANGER INDICATES AN IMMINENTLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURYEquipotential Ground Symbol 1-5. SAFETY ContinuedWaste Electrical and Electronic Equipment WEEE Symbol Shock Hazard Symbols OR Hot Surface Symbols ORPage 2-2. UNPACKING SECTION 2. INSTALLATION2-1. INTRODUCTION To prevent severe burns from splashing hot oil 2-3. SELECTING THE FRYER LOCATION 2-4. LEVELING THE FRYER2-6. GAS SUPPLY 2-6. GAS SUPPLY Continued Model EEG-141, 142, 143 2-6. GAS SUPPLY Continued2-9. ELECTRICAL REQUIREMENTS 2-7. GAS LEAK TEST 2-8. GAS PRESSURE REGULATOR SETTING2-11. LIGHTINGAND SHUTDOWN OF THE BURNERS 2-9. ELECTRICAL REQUIREMENTS Continued 2-10. MOTOR BEARINGSModel EEG-141, 142, 143 2-12. DIMENSIONSPage 3-1. OPERATING COMPONENTS SECTION 3. OPERATIONRefer to explanations on the next pages Bulk Oil Supply Fryers OnlyDescription 3-1. OPERATING COMPONENTS ContinuedFunction 3-1 3-1 3-1 3-1 3-1 3-1 3-13-1. OPERATING COMPONENTS ContinuedDescription FunctionFunction DescriptionDrain Valve Knob Vat Covers3-2. SET-UP MODE 3-3. FILLING OR ADDING OIL 3-4. MORNING START-UP PROCEDURES 3-5. BASIC OPERATION 3-6. IDLE MODE Manual Top-Off 3-7. OIL GUARDIAN Auto Top-Off 3-8. SELECTINGA PRODUCTWITHADIFFERENT SETPOINT 3-9. REPLACING THE JIB Filling Oil Reservoir Removing/Cleaning Reservoir3-10. MODEL EEG-141 OIL RESERVOIR 3-11. SMARTFILTER EXPRESS 3-11. SMARTFILTER EXPRESS Continued Filter Error3-12. DAILY FILTERING 3-12. DAILY FILTERING Continued 3-13. DISCARDING OIL FROM VAT USING OPTIONAL OIL DISCARD SHUTTLE 3-14. DISCARDING OIL FROM VAT USING OPTIONAL BULK OIL DISPOSE SYSTEM 3-15. CHANGING THE FILTER PAD 3-15. CHANGING THE FILTER PAD Continued Be sure that the drain pan, bottom screen, crumb catcher, and the retaining ring are thoroughly dry before placing filter pad into pan as water will dissolve the filter pad 3-16. REMOVING AND CLEANING BASKET REST3-15. CHANGING THE FILTER PAD Continued 3-17. CLEAN-OUT MODE 3-17. CLEAN-OUT MODE Continued “RINSE COMPLETE” “YES NO” 3-17. CLEAN-OUT MODE ContinuedTo prevent oil leaking, and to keep filtering process operating properly, the filter drain pan o-rings should be inspected for nicks and tears at least every 3 months. Figure 3-18. CHECK/REPLACE FILTER DRAIN PAN O-RINGSand the actual oil temperature shows in the Actual Oil TemperatureSet-point Temperature Recovery Information for each VatProcedureFrequency 3-21. PREVENTIVE MAINTENANCE SCHEDULE3-22. CLEAN BLOWER & VENTS Page 4-1. INFORMATION MODE DETAILS SECTION 4. INFORMATION MODEDISPLAY EX 4-1. INFORMATION MODE DETAILS ContinuedFUNCTION Press button to start viewing the cook data 4-1. INFORMATION MODE DETAILS ContinuedPress the right to view data for other days of weekDISPLAY EX 4-1. INFORMATION MODE DETAILS ContinuedFUNCTION 4-1. INFORMATION MODE DETAILS Continued Reset usage dataFUNCTION DISPLAY EXSECTION 5. PRODUCT PROGRAM MODE 5-1. MODIFYING PRODUCT SETTINGSChange Product Names Assign ButtonTo Change Times and Temperatures 5-1. MODIFYING PRODUCT SETTINGS ContinuedAlarms 1 Quality Timer hold timeLoad Compensation, Load Compensation Reference, Full Heat, PC Factor MixFilterdAfterFil TrackingX Number of Loads5-1. MODIFYING PRODUCT SETTINGS Continued 6-1. SPECIAL PROGRAM MODE SECTION 6. LEVEL 2 PROGRAMMINGTech Mode Stats6-1. SPECIAL PROGRAM MODE Continued Audio Volume SP-4Degrees Fahrenheit or Celsius SP-1 Language SP-2Audio Tone SP-5 Idle Mode Enabled SP-7Liquid or Solid Cooking Oil Used SP-6 6-1. SPECIAL PROGRAM MODE ContinuedMIXED Filter Tracking Mode SP-86-1. SPECIAL PROGRAM MODE Continued CycleIf GLOBAL is selected, press button Filter Tracking Mode SP-8 Continued GLOBAL6-1. SPECIAL PROGRAM MODE Continued Clean-Out Temperature SP-12 Clean-Out Time SP-11Cooking Indicator SP-15 Polish Duration SP-92nd Language SP-16 2nd Volume SP-17Engery Save Mode SP-18 Fryer Type SP-19Bulk Oil Supply SP-22 Autolift Enabled SP-21Bulk Oil Disposal SP-23 Serial Number Log SP-24Usage Code Change SP-26 Program Code Change SP-25 ContinuedDispose Requires Code ? SP-27 Longer Fill Time SP-286-3. DATA LOGGING, HEAT CONTROL, TECH, STAT, AND FILTER CONTROL MODES 6-2. CLOCK SETProblem SECTION 7. TROUBLESHOOTING 7-1. TROUBLE SHOOTING GUIDECause CorrectionProblem 7-1. TROUBLE SHOOTING GUIDEContinued CauseDISPLAY 7-2. ERROR CODESCAUSE CORRECTIONDISPLAY 7-2. ERROR CODESCAUSE CORRECTIONPage Toll free in USA Henny Penny Corporation P.O.Box Eaton,OH