Electrical Requirements | Henny Penny EEG-143, EEG-142, EEG-141

2-9. ELECTRICAL REQUIREMENTS (Continued)

2-10. MOTOR BEARINGS

2-11. LIGHTINGAND SHUTDOWN OF THE BURNERS

609

Model EEG-141, 142, 143, 144

To avoid electrical shock, do not disconnect the ground (earth) plug. This fryer must be adequately and safely grounded (earthed). Refer to local electrical codes for correct grounding (earthing) procedures or in absence of local codes, with The National Electrical Code, ANSI/NFPA No.

70-(the current edition). In Canada, all electrical connections are to be made in accordance with CSA C22.2, Canadian Electrical Code Part 1, and/or local codes.

Disconnect power supply before a thorough cleaning or servicing the fryer

The electric motor bearings are permanently lubricated. DO NOT LUBRICATE.

1.Turn the power switch to the OFF position.

2.Wait at least 5 minutes and then turn the power switch to the ON position.

3.Press button on the controls (left or right).

4.The burner lights and operates in a Melt Cycle until the shortening reaches a preset temperature.

6.Once the display shows a product selection or a double dashes, press the desired product button.

The fryer is equipped with a ignition spark module which has a set ignition safety time (TSA) of 90 seconds.

To shutdown burner:

1. Press

button on the controls (left or right).

2.Turn the power switch to the OFF position. NOTE: This turns off all vats.

2-7

Image 19

Henny Penny EEG-143, EEG-142, EEG-141, EEG-144 Electrical Requirements, Motor Bearings Lightingand Shutdown of the Burners

Contents

OPERATOR’S Manual Page FM05-057-C Revised Technical Data for CE Marked Products Limited Warranty for Henny Penny Equipment Table of Contents Section Table of Contents Page Introduction FeaturesProper Care Assistance Safety Safety Page Unpacking Installation Selecting the Fryer Location Leveling the Fryer GAS Supply GAS Supply GAS Supply Model EEG-141, 142, 143 Motor Bearings Lightingand Shutdown of the Burners Electrical Requirements Dimensions Page Refer to explanations on the next pages Operation Operating Components Description Operating ComponentsFunction Description Function JIB VAT Type Full or Split SET-UP Mode Fill POT from Bulk Filling or Adding OIL Morning START-UP Procedures Basic Operation Idle Mode Selectinga Product Withadifferent Setpoint Replacing the JIB OIL Guardian Auto Top-Off Filling Oil Reservoir Removing/Cleaning ReservoirModel EEG-141 OIL Reservoir Smartfilter Express Smartfilter Express Filter Error Check Filter Pan a new filter pad should be used on Daily Filtering Daily Filtering Discarding OIL from VAT Using Optional OIL Discard Shuttle Express FILTER? Changing the Filter PAD Changing the Filter PAD Removing and Cleaning Basket Rest CLEAN-OUT CLEAN-OUT Mode CLEAN-OUT Mode Rinse Complete YES no CHECK/REPLACE Filter Drain PAN O-RINGS Filter Button Stats Actual Oil TemperatureRecovery Information for each Vat Info Button Stats ProcedureFrequency Preventive Maintenance Schedule Clean Blower & Vents Page Information Mode Details Information Mode Function Display EX Details TUE NEW OIL Reset usage data Change Product Names Product Program Mode Modifying Product SettingsAssign Button Quality Timer hold time Modifying Product SettingsTo Change Times and Temperatures Alarms 1 MixFilterdAfterFil TrackingX Number of Loads Filter Control Level 2 Programming Special Program Mode Language SP-2 Special Program ModeAudio Volume SP-4 Degrees Fahrenheit or Celsius SP-1 Audio Tone SP-5 Idle Mode Enabled SP-7Liquid or Solid Cooking Oil Used SP-6 Mixed Filter Tracking Mode SP-8 If Global is selected, press button Global Polish Duration SP-9 Clean-Out Time SP-11Clean-Out Temperature SP-12 Cooking Indicator SP-15 Fryer Type SP-19 2nd Volume SP-17Engery Save Mode SP-18 2nd Language SP-16 Serial Number Log SP-24 Autolift Enabled SP-21Bulk Oil Supply SP-22 Bulk Oil Disposal SP-23 Let User Exit Fill SP-29 Usage Code Change SP-26Dispose Requires Code ? SP-27 Longer Fill Time SP-28 Model EEG-141, 142, 143 Problem Cause Correction Troubleshooting Trouble Shooting Guide Remove the right side panel Display Cause Correction Error Codes Closed Error Codes Display Cause CorrectionPage Henny Penny Corporation Box Eaton,OH Toll free in USA