Hitachi SJ700-2 Series service manual B034

	Code
	b034
	b035
Others	b036
	b037
	b038
	b039
	b040
limitation	b041
	b042
Torque
	b043
	b044
	b045
	b046
power	b050
	b051
momentaryatoperation failure
	b052
	b053
Non-stop	b054
	b056
	b055
	b060
	b061
	b062
	b063
comparator	b064
	b065
Window	b066
	b067
	b068
	b070
	b071
	b072

			Default
Function name	Monitored data or setting				Note
		_FF	_FEF	_FUF
Run/power-on warning time	0. to 9999. (0 to 99990), 1000 to 6553 (10000 to 655300) (hr)		0.
Rotational direction restriction	00 (enabling both forward and reverse rotations), 01 (enabling only		00
	forward rotation), 02 (enabling only reverse rotation)
Reduced voltage start selection	0 (minimum reduced voltage start time) to 255 (maximum reduced voltage		6
	start time)
Function code display restriction	00 (full display), 01 (function-specific display), 02 (user setting), 03 (data		04
	comparison display), 04 (basic display)
Initial-screen selection	00 (screen displayed when the STR key was pressed last), 01 (d001), 02		01
	(d002), 03 (d003), 04 (d007), 05 (F001)
Automatic user-parameter	00 (disabling), 01 (enabling)		00
setting function enable
Torque limit selection	00 (quadrant-specific setting), 01 (switching by terminal), 02 (analog		00
	input), 03 (option 1), 04 (option 2)
Torque limit (1) (forward-driving	0. to 200. (%), no (disabling torque limitation)		150.
in 4-quadrant mode)
Torque limit (2)
(reverse-regenerating in	0. to 200. (%), no (disabling torque limitation)		150.
4-quadrant mode)
Torque limit (3) (reverse-driving	0. to 200. (%), no (disabling torque limitation)		150.
in 4-quadrant mode)
Torque limit (4)
(forward-regenerating in	0. to 200. (%), no (disabling torque limitation)		150.
4-quadrant mode)
Torque limit LADSTOP enable	00 (disabling), 01 (enabling)		00
Reverse Run protection enable	00 (disabling), 01 (enabling)		00
Controller deceleration and stop	00 (disabling), 01 (nonstop deceleration to stop), 02 (DC voltage constant		00
on power loss	control, with resume), 03 ( without resume)
DC bus voltage trigger level	0.0 to 999.9, 1000. (V)		220/440
during power loss
Over-voltage threshold during	0.0 to 999.9, 1000. (V)		360/720
power loss
Deceleration time setting during	0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)		1.00
power loss
Initial output frequency decrease	0.00 to 10.00 (Hz)		0.00
during power loss
Proportional gain setting for	0.00 to 2.55		0.20
nonstop operation at power loss
Integral time setting for nonstop	0.000 to 9.999 /10.00 to 65.53 (s)		0.100
operation at power loss
Maximum-limit level of window	0. to 100. (lower limit : b061 + b062 / 2) (%)		100
comparators O
Minimum-limit level of window	0. to 100. (lower limit : b060 - b062 / 2) (%)		0
comparators O
Hysteresis width of window	0. to 10. (lower limit : b061 - b062 / 2) (%)		0
comparators O
Maximum-limit level of window	0. to 100. (lower limit : b064 + b066 / 2) (%)		100
comparators OI
Minimum-limit level of window	0. to 100. (lower limit : b063 - b066 / 2) (%)		0
comparators OI
Hysteresis width of window	0. to 10. (lower limit : b063 - b064 / 2) (%)		0
comparators OI
Maximum-limit level of window	-100. to 100. (lower limit : b067 + b068 / 2) (%)		100
comparators OI
Minimum-limit level of window	-100. to 100. (lower limit : b066 - b068 / 2) (%)		0
comparators O/OI/O2
Hysteresis width of window	0. to 10. (lower limit : b066 - b067 / 2) (%)		0
comparators O/OI/O2
Operation level at O	0. to 100. (%) or "no" (ignore)		no
disconnection
Operation level at OI	0. to 100. (%) or "no" (ignore)		no
disconnection
Operation level at O2	-100. to 100. (%) or "no" (ignore)		no
disconnection

1 - 8