Enww | HP 9000s manual

●Tension winding: place the take-up reel roller in the bottom position.

1. Tension roller

NOTE Do not change the order of the seven tension rollers as their outside diameters are different. Changing the order will cause media skew. Distribute the tension rollers to support the full width of the media.

1.Position each tension rollers by unscrewing the three screws to the left of the roller. Tighten the screws when the roller is in its final position.

2.Press the ONLINE key to view the MEDIA REG menu.

3.Press ▼ to select MEDIA REG.

42

Chapter 3 How do I load/unload media?

ENWW

Image 50

HP 9000s manual Enww

Contents

HP Designjet 9000s Printer series Legal notices Table of contents How do I… ink topics Problem is… troubleshooting topics Tell me about waste management 158 Tell me about printer specifications Introduction Using this guide Printers main components Front view Rear view Heaters Printers front panel Enww Enww Basic printer operations and keys Heaters front panel General warnings Safety precautionsDefining heater parameters Safety precautions General cautions Regular inspection and maintenance Handling precautionsPower supply Printer Enww How do I perform basic operations? Choose the system configurationConnection procedure Connect to a computer Turn the power on/off Turn on the printer Enww Enww Turn off the printer Turn the power offTurn on the heater Turn off the heater Enww Enww How do I load/unload media? Install a media roll in the printer Enww Enww Enww Enww Enww Enww Enww Remove a media roll from the printer Replace a jammed media roll Load cut sheet Load cut sheet Enww Enww Enww Use the take-up reel Set the take-up reel winding direction Enww Define the take-up reel winding mode Enww Load media on to the take-up reel Enww Enww Enww Use the media edge guard Enww Set the fan guard lever Enww How do I... printing topics Perform a manual media feed Use manual nesting Enww Enww Increase/reduce pressure on media Pause or cancel print jobs Pause or cancel print jobs Enww How do I… ink topics Replace an ink cartridge Enww Change the printhead height Enww Enww Enww Regular maintenance guide How do I maintain the printer? Daily printhead maintenance Category Inspection/Maintenance Wiper blade cleaning Enww Enww Enww Enww Capping unit cleaning Enww Leave the printer off for two to four weeks Ink system storage Clean ink system Leave the printer off for less than two weeks Clean the exterior of the printer Charge the ink system Clean the rear cover and media feed Clean the platen Clean the platen Replace the waste ink bottle Replace the waste ink bottle Enww Normal printhead recovery Enww IQ Print Enww How do I get the best image quality? Print the Image Quality print Print the Image Quality print Interpret the image quality print Manage media types Copy a media type to create a new one Create a new media type Modify media type settings Delete a media type Calibrate the printer Calibrate media advance Draft Enww Perform printhead position adjustment Back feed adjustment print Parameters Enww Adjust heater and print mode settings QUALITY2 DENSITY2 Problem is… troubleshooting topics Problem is… checklist Symptom Items to be checked Corrective measures Head crash Items to be checked Corrective measures Enww Head crash 107 Ink cartridge is near expiry date Ink cartridge is not installedInk cartridge is not detected Ink cartridge has passed its expiry date An error messageService errors Engine error messages Operator error messagesPOC error messages System error messages An error message 111 Media crash Waste ink bottle is not installedWaste ink bottle is full Media Error LED is flashing Other messages An abnormal sound Problem is print quality This section explains how to solve print quality problems 116 Problem is print quality Tell me about… basic knowledge topics Operating conditions Installation spaceOperating temperature and humidity levels Environmental conditions Places where the printer must not be installed Power supplyPower Exhaust attachment Front panel messages and printer stateDryer Messages on the front panel Online state print pause mode display Online state idle mode displayOnline state print mode display Online state print information mode display Offline menu mode display Shutdown state display 124 Tell me about… basic knowledge topics Disposing of media Tell me about mediaStoring media Handling prints Using mediaOther precautions Tell me about the ink system Ink cartridges Enww Replacing an ink cartridge Ink cartridge storage and disposal HP 790 Waste Ink Bottle HP 790 Cap Cleaning LiquidPrecautions for handling the waste ink bottle HP 790 Storage Kit HP 790 Wiper Cleaning Liquid and DropperHP Cleaning Swabs HP 790 Ink System Cleaning Kit 134 Tell me about the ink system Tell me about waste management General recommendations General recommendations 137 138 Tell me about waste management Tell me about front panel menus Menu structure Making front panel selections and settingsMenu operations To define a value Character list Replacing ink cartridges during printing INK menu & messagesReplacing an empty ink cartridge Ink cartridge is empty Media menuInk cover is open Media REG menu Media advance value Media ADV Value Setting a media type name Rename MediaSelecting a media type number Select Media Print direction setting Print Direction Manufacturing default media advance value Mfng VALPrint mode setting Print Mode Dry time value DRY Time Value Flatten time Flatten Time Use media edge guard USE Edge Guard Media advance mode Media ADV ModeTake-up reel mode TUR Mode Leading edge mode Leading Edge Vacuum level setting Vacuum Level Normal Normal fan suction level LOW Low fan suction level Color stripe setting Color Stripe Printhead firing mode setting Image Gradient Bidirectional print position Right adjustment YY Bidir Defr Printhead height setting PH Height VALBidirectional print position Left adjustment YY Bidir Defl Printhead cleaning mode PH Cleaning Media back feed adjustment Back Adjust VAL Heater preference Heater Pref Print mode preference Print Mode PrefMedia advance preference Advance Pref Printhead rest period PH Rest Period Printhead rest time PH Rest Time Printhead temperature rest PH Temp RestDefault values for media types Deleting a media type Delete Media Media REG menu 157 Media advance calibration Media advance calibration print Ink system optimization INK SYS OPT Media back feed adjustment valuePH. Main menu Washing printheads Wash Printheads Cap cleaning CAP CleaningWiper cleaning Wiper Cleaning Printhead height PH Height ADJ PH.RECOVERY menuFeed menu Printer menu Configuration print Config PrintError log information print Error LOG Print History print History Print Printhead nozzle position adjustment #YY PH ROW VAL Adjust menuAdjustment pattern print Test Prints Printhead position adjustment #YY PH to PH VAL Bidirectional print position Left adjustment YY Bidir F.D L Language for front panel Language Setup menuBoot version display Boot Version Acoustic warning Beep ICB board version display Carriage PCA Version display F/W VersionMain PCA version display Main PCA VER Asic version display Asic VER Factory default setting Factory Default System date setting System DateSystem time setting System Time Heater F/W version display Heater FW VER USB speed USB Speed Tell me about the heaters Heaters Heater temperature settings Heater preset temperature by medium Maintaining the preset temperature Flow of heater temperature settingTemperature control Heater front panel Maintaining the standby temperatureDisplay in normal mode Turning off the heaters Setup items and parameters Heater parameter setup modeDisplay heater AC power is turned off Display heater on Heater error messages Enww Tell me about printer specifications Specifications Specification / Function Ecological specifications 180 Tell me about printer specifications Tell me about ordering supplies and accessories Ordering supplies Ordering media Ordering accessories HP Paper 184 Tell me about ordering supplies and accessories Tell me about getting help HP Customer Care HP Designjet Online Accessories Index Enww