2. Printer Settings (20 ppm copier)

Item No.

Item

Display message

Available settings

Remarks

 

 

 

 

 

23

Page Protect

Page Protect

Auto, On

 

 

If “AUTO” is selected here, the machine will

 

 

 

 

monitor the data and, if necessary, will

 

 

 

 

automatically turn Page Protect ON. If a

 

 

 

 

“Print overrun” error does happen to occur

 

 

 

 

even then, the machine will automatically

 

 

 

 

change the Page Protect setting to “ON”.

 

 

 

 

 

 

 

 

24

Line Feed (LF) handling

LF Action

LF only,

Allows you to set different line

 

 

 

CR and LF,

feed handling for the parallel

 

 

 

Ignore LF

interface and the Network Card

 

 

 

 

(option). Select the desired

 

 

 

 

interface under the “Interface

 

 

 

 

selection” setting (item No.: 2).

 

 

 

 

 

25

Carriage Return (CR) handling

CR Action

CR only,

Allows you to set different carriage

 

 

 

CR and LF,

return handling for the parallel

 

 

 

Ignore CR

interface and the Network Card

 

 

 

 

(option). Select the desired

 

 

 

 

interface under the “Interface

 

 

 

 

selection” setting (item No.: 2).

 

 

 

 

 

26

Wide A4 ON/OFF

Wide A4

On, Off

 

 

Increases the printing area on A4 size paper.

 

 

 

 

 

 

 

 

27

Smoothing ON/OFF

KIR Mode

On, Off

 

 

Allows a printing resolution of an interpo-

 

 

 

 

lated 2400 dpi x 600 dpi through the

 

 

 

 

smoothing process.

 

 

 

 

 

 

 

 

28

Draft Mode ON/OFF

Draft

On, Off

 

 

Allows printing in a toner-saving mode. This

 

 

 

 

mode is especially suited for test pages, etc.,

 

 

 

 

where high printing quality is not required.

 

 

 

 

 

 

 

 

29

Printing resolution

Resolution

300 dpi, 600 dpi

 

 

 

 

 

 

30

RAM disk ON/OFF

RAM DISK Mode

On, Off

At least 16 MB of additional

 

 

 

 

memory (option) must be installed.

 

 

 

 

 

31

RAM disk size

RAM DISK Size

01 - 99 (MBytes)

Displayed only when “On” is

 

Sets the amount of memory that will be used

 

 

selected under the “RAM disk ON/

 

as a RAM disk. The maximum size that can

 

 

OFF” setting (item No.: 30).

 

be selected is the total amount of memory

 

 

 

 

installed minus the amount used by the

 

 

 

 

system (9 MB).

 

 

 

 

 

 

 

 

32

Reading data

Read Data

Select the name of

Displayed only when there is

 

Reads the selected data on the RAM disk.

 

the partition which

appropriate data in the RAM disk.

 

 

 

holds the data from

 

 

 

 

among those

 

 

 

 

displayed.

 

 

 

 

 

 

33

Reading program data

Read Program

Select the name of

Displayed only when there is

 

Reads the selected program data on the

 

the partition which

appropriate program data in the

 

RAM disk.

 

holds the program

RAM disk.

 

 

 

from among those

 

 

 

 

displayed.

 

 

 

 

 

 

34

Writing data

Write Data

OK

Displayed only when “On” is

 

If “OK” is selected here, the machine will

 

 

selected under the “RAM disk ON/

 

enter a “waiting for data” state until data is

 

 

OFF” setting (item No.: 30).

 

sent from the host computer. To exit this

 

 

 

 

state, select the “GO” command in the

 

 

 

 

printer mode and then press the Enter key.

 

 

 

 

 

 

 

 

2-9

Page 20
Image 20
IBM Printing System Line Feed LF handling, Carriage Return CR handling, Reading data, Reading program data, Writing data