009(continued)

Solve the problems that caused the SRN. Return to Step 001 on page 2324-2.

010

(From step 006)

– Find your SRN in the following table, then do the appropriate actions.

Note: If you still do not have any of these SRNs, you are in the wrong MAP.

SRN

Cause

 

 

 

 

 

 

 

Action

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

46000

An

array

is

in

the Offline

stateGo.to Step

011.

 

 

 

 

 

 

 

 

 

 

 

 

 

47000

You have

more

than the maximum

Go to Step

018

on

page 2324-5.

 

number of

arrays

allowed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

47500

A partial

loss

of data has

occurredGoto .Step

019

on

page 2324-5.

 

 

 

 

 

 

 

 

 

 

 

 

 

49000

An

array

is

in

the

Degraded

stateGoto.

Step

031

on

page 2324-7.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

49100

An

array

is

in

the

Exposed

 

stateGo.to

Step

041

on

page 2324-9.

 

 

 

 

 

 

 

 

 

 

 

 

49700

The

parity

on

an

array is

not Gocompleteto Step.

051

on

page 2324-11.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

011

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(From

 

step

010)

 

 

 

 

 

 

 

 

 

 

 

 

 

An

array

is

in

the

Offline state if at least one

member disk

drive

of

the

array

but

more

than

one

member

disk

drive

is

missing. Such

a

condition

can occur

if

at

le

two

 

disk

drives in

the

array

have

failed, or are

not

available

to

the

array

at

ARE

ANY

DISK

DRIVES

MISSING

OR WITHOUT POWER, OR HAVE

ANY

DISK

 

 

 

 

 

 

 

DRIVES

BEEN

RE-CABLED

(not

necessarily by

you)?

 

 

 

 

 

 

 

 

 

Yes

 

 

No

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

012

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Go to Step 014 on page 2324-4.

013

You must now restore the original configuration:

– Using

the

DOS

Configurator,

select

the

appropriate

adapter, then from

the

adapter

menu

selectRAID 5

Resources

.

 

 

 

 

 

 

– Using

the

RSM

configurator,

go to

the

logical view

and select either

RAID

Lists

System (PC) List for JBOD. (Step 013 continues)

MAPs 2324-3

Page 75
Image 75
IBM SY33-0193-00 manual Not Necessarily by You?, Action