Contents
Safety and Environmental Notices . . . . . . . . . . . . . . . . . vii
Danger Notice . . . . . . . . . . . . . . . . . . . . . . . . . vii Caution Notice . . . . . . . . . . . . . . . . . . . . . . . . . vii
Attention Notice | viii |
Laser Safety and Compliance | viii |
Preface | ix |
Intended Audience | ix |
Related Publications | ix |
IBM Ultrium Publications | ix |
IBM Fibre Channel Publications | ix |
Other Publications . . . . . . . . . . . . . . . . . . . . . . . ix Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . 1
Cartridge Compatibility | . . . . | . | 2 |
Speed Matching and Channel Calibration | . . . . | . | 2 |
Sleep Mode | . . . . | . | 2 |
Supported Servers and Operating Systems | . . . . | . | 3 |
SCSI Attachment | . . . . | . | 4 |
Physical Characteristics of the SCSI Interface | . . . . | . | 4 |
Speed | . . . . . 4 | ||
Address Assignments . . . . . . . . . . . . . . . . . . . . . . 5 | |||
Installing, Removing, or Resetting a Drive on an Active SCSI Bus | . . . . | . | 5 |
Fibre Channel Attachment . . . . . . . . . . . . . . . . . . . . . 6 Supported Topologies . . . . . . . . . . . . . . . . . . . . . . 6
Speed | . . . . . . . . | . | 7 | ||
Address Assignments | . . . . . | . . | . . 7 | ||
World Wide Names | . . | . . 8 | |||
Physical Characteristics of the Fibre Channel Interface | . . . . . . . . | . | 8 | ||
Installing, Removing, or Resetting a Drive on an Active Fibre Channel . . . | . | 8 |
Supported Device Drivers | . | 9 |
Chapter 2. | Specifications | . . . . . . . . | . . | . | . | . | . | 11 | |
Chapter 3. | Installing the Tape Drive . . | . . . . . . . . | . . | . | . | . | . | 13 | |
Rear View of the SCSI Drive | . . . . . . . . | . . | . | . | . | . | 14 | ||
Rear View of the Fibre Channel Drive . . | . . . . . . . . | . . | . | . | . | . | 15 | ||
Step 1. | Unpack the Drive | . . . . . . . . | . . | . | . | . | . | 16 | |
Step 2. | Remove Power from the Enclosure | . . . . . . . . | . . | . | . | . | . | 16 | |
Step 3. Set the SCSI ID or Arbitrated Loop Physical Address . . . . . . . . 17
Setting the SCSI ID (SCSI Drive Only) | . | . | 17 | |
Setting the Arbitrated Loop Physical Address (Fibre Channel Drive Only) |
|
| 19 | |
Step 4. Change the Link Services of the Drive (optional) | . | . | 24 | |
Step 5. Mount the Tape Drive into the Enclosure | . | . | 26 | |
Step 6. | Connect and Test Power to the Tape Drive | . | . | 27 |
Step 7. | Connect the Internal SCSI or Fibre Channel Cable | . | . | 27 |
Step 8. | Connect the Internal LDI Cable (optional) | . | . | 28 |
Step 9. | Run Drive Diagnostics | . | . | 28 |
Step 10. Install the Device Drivers | . | . | 28 | |
Step 11. Connect the External SCSI or Fibre Channel Interface to the Server |
|
| 28 | |
Connect the External SCSI Interface to the Server | . | . | 28 | |
Connect the External Fibre Channel Interface to the Server | . | . | 29 | |
Step 12. Connect the External LDI Interface to the Server (optional) . . . | . | . | 29 | |
© Copyright IBM Corp. 2002 | iii |
