Rear View of the Fibre Channel Drive | IBM T400F specification

Rear View of the Fibre Channel Drive

Power connector

Feature switches

Loop identifier (LID)/status connector

Fibre Channel (FC) configuration/status connector

Fibre Channel connector

Library/Drive Interface (LDI or RS-422 interface) connector

Figure 3. Rear view of the IBM TotalStorage LTO Ultrium 2 Tape Drive Model T400F (Fibre Channel drive)

Chapter 3. Installing 15

Image 27

IBM T400F manual Rear View of the Fibre Channel Drive

Contents

Setup, Operator, and Service Guide Page Setup, Operator, and Service Guide First Edition November Contents Operating the Tape Drive Contents Vi IBM TotalStorage LTO Ultrium 2 Tape Drive Vii Safety and Environmental Notices Sample caution notices follow Laser Safety and Compliance Preface IBM TotalStorage LTO Ultrium 2 Tape Drive Introduction Sleep Mode Cartridge CompatibilitySpeed Matching and Channel Calibration Supported Servers and Operating Systems Supported Servers Supported Operating SystemsSupported SAN Components for Fibre Channel Attachment Physical Characteristics of the Scsi Interface Scsi AttachmentSpeed Address Assignments Fibre Channel Attachment Supported TopologiesType of Fibre Channel Connection to Server Speed World Wide Names Physical Characteristics of the Fibre Channel Interface Supported Device Drivers IBM TotalStorage LTO Ultrium 2 Tape Drive Other Specifications for both interface types SpecificationsSpecification Measurement Physical Specifications Power Specifications 26C Installing the Tape Drive Rear View of the Scsi Drive Rear View of the Fibre Channel Drive Unpack the Drive Remove Power from the Enclosure Setting the Scsi ID Scsi Drive Only Setting the Scsi ID with JumpersSet the Scsi ID or Arbitrated Loop Physical Address Setting the Scsi ID with a Scsi ID Switch Setting the Scsi ID Through the LDI InterfaceSupplying Termpower Scsi Drive Only Installing Setting the Loop ID to Provide Status About the Loop LID Setting the Loop ID to Provide Additional Loop IDs Alpa LID Fibre Channel Pin Characteristic Through Speed Selection Change the Link Services of the Drive optional Fibre Channel Pin Characteristic Through Mount the Tape Drive into the Enclosure Connect the Internal Scsi or Fibre Channel Cable Connect and Test Power to the Tape Drive Connect the External Scsi Interface to the Server Run Drive DiagnosticsInstall the Device Drivers Connect the Internal LDI Cable optional Configure the Tape Drive to the Server, Switch, or Hub Connect the External Fibre Channel Interface to the ServerConnect the External LDI Interface to the Server optional IBM TotalStorage LTO Ultrium 2 Tape Drive Front view of the IBM TotalStorage LTO Ultrium 2 Tape Drive Operating the Tape Drive Color and Condition Meaning Status Light Status Light Unload Button Single-Character DisplaySingle Red Dot Inserting a cartridge into the Ultrium 2 Tape Drive Inserting a Tape Cartridge Removing a Tape Cartridge Cleaning the Drive Head Selecting a Diagnostic or Maintenance Function Function Code 3 Create FMR Tape Function Code 2 Update Tape Drive Firmware from FMR Tape Function Code 4 Force a Drive Dump Running a Scsi Wrap Test Function Code 6 Run Scsi or Fibre Channel Wrap Test Running a Fibre Channel Wrap Test Testing the Circuitry at the Fiber Cable Function Code 8 Convert FMR Tape to Scratch Tape Function Code 7 Run LDI or RS-422 Wrap Test Function Code 9 Display Error Code Log Function Code a Clear Error Code LogFunction Code C Insert Cartridge into Tape Drive Function Code F Fast Read/Write Test Function Code E Test Cartridge & Media Function Code P or U Enable or Disable Post Error Reporting Function Code H Test HeadFunction Code L Reserved for Future Use Exiting Maintenance Mode Updating the FirmwareUpdating Firmware through the Library/Drive Interface Updating the Firmware with an FMR Tape Cartridge IBM TotalStorage LTO Ultrium 200 GB Data Cartridge Using the Media Data Cartridge Cleaning Cartridges Handling the Cartridges Setting the Write-Protect Switch Ensure Proper Packaging Provide Training Perform a Thorough Inspection Provide Proper Acclimation and Environmental Conditions Checking for gaps in the seams of a cartridge Handle the Cartridge Carefully Example Improper Placement of Leader Pin Examples of Cartridge Problems Repositioning a Leader Pin Repositioning or Reattaching a Leader Pin Remove the rewind tool by pulling it away from the cartridge Cartridge manual rewind tool see Reattaching a Leader Pin IBM TotalStorage LTO Ultrium 2 Tape Drive A67E0036 On the leader pin Using the Media Temperature 10 to 45C 16 to 32C 16 to 25C −23 to 49C Disposing of Tape Cartridges Ordering Media SuppliesIBM Part Number Product Description America Europe and Asia Ordering Custom Bar Code Labels If the problem is this Do this Resolving Problems If the error or message was Do this Presented by Methods of Receiving Errors and Messages Code Cause and Action Descriptions and Corrective Actions for Errors and Messages Code Cause and Action For Problems with Reading Data For Problems with Writing Data For Fibre Channel drive For Scsi drive Using Sense Data Press F4 to view the sense data see the example in Figure Obtaining Error Information from the RS/6000 or pSeries Example of a Drive Error Log Example of a Scsi Bus Error Using the Drive to Obtain a Dump Using a Device Driver Utility to Obtain a DumpObtaining a Drive Dump Viewing the Drive Error Log Resolving Problems Reported by the Server Fixing Scsi Bus ErrorsFixing a Consistent Error with a Single Drive on a Scsi Bus IBM TotalStorage LTO Ultrium 2 Tape Drive Starting Problem Determination Fixing Fibre Channel Errors Fixing a Consistent Error in a Point-to-Point Topology Fixing Intermittent Fibre Channel Errors Resolving Media-Related Problems Removing a Scsi Tape Drive from an Enclosure Servicing the Tape Drive Removing a Fibre Channel Tape Drive from an Enclosure Removing the Cartridge Manually Removing a Tape Cartridge Determining whether the tape is broken Servicing Fixing an Internal Jam Removing the top cover of the drive Rewinding the leader pin into the tape cartridge Guiding the leader block into the home position IBM TotalStorage LTO Ultrium 2 Tape Drive Servicing Rotating the loader motor gear until the cartridge ejects Appendix A. Tools and Supplies IBM TotalStorage LTO Ultrium 2 Tape Drive Appendix B. TapeAlert Flags TapeAlert Flags Supported by the DriveFlag Description Action Required Number Hex 0Ch 22h IBM TotalStorage LTO Ultrium 2 Tape Drive IBM Trademarks Federal Communications Commission FCC Class B Statement Industry Canada Class B Emission Compliance StatementAvis de conformité à la réglementation d’Industrie Canada European Union EU Electromagnetic Compatibility Directive Germany Electromagnetic Compatibility DirectiveJapan Vcci Class B ITE Electronic Emission Statement Getting Help Warranty Glossary Numbers and Symbols Data compression. See compression See Celsius Fibre Channel-Arbitrated Loop FC-AL topology. a Fibre Channel configuration/status connector FMR tape. See field microcode replacement tape LAN. See local area network LDI. See Library/Drive Interface Media capacity. See capacity Log sense data. See Scsi log sense data Transfer rate Native sustained data transfer rate. See data See second SAN. See Storage Area Network Glossary Ultrium 2 Tape Drive. See IBM TotalStorage LTO TotalStorage LTO Ultrium 2 Tape Drive. See IBM WAN. See wide area network IBM TotalStorage LTO Ultrium 2 Tape Drive AIX Alpa Index LID Cables Connecting to a bus Fixing errors Sleep mode Wrap test, running Fibre Channel LDI or RS-422 IBM TotalStorage LTO Ultrium 2 Tape Drive Page GA32-0455-00