INTEL386™ EX MICROPROCESSOR USER’S MANUAL
Index-8
SSIOTBUF, 13-16, 13-24, D-61
TBRn, 11-15, 11-23, D-61
TMRCFG, 5-13, 10-4, 10-21, D-62
TMRCON, 10-4, 10-25, 10-28, 10-30, D-63
TMRn, 10-4, 10-26, 10-29, 10-32, D-64, D-65
UCSADH, 14-14, 14-17, D-8
UCSADL, 14-14, 14-18, D-9
UCSMSKH, 14-14, 14-19, D-10
UCSMSKL, 14-14, 14-20, D-11
WDTCLR, 17-7
WDTCNTH, 17-7, 17-8, D-67
WDTCNTL, 17-7, 17-8, D-67
WDTRLDH, 17-7, 17-10, D-68
WDTRLDL, 17-7, 17-10, D-68
WDTSTATUS, 17-7, 17-9, D-69
reload event, 17-4
Reserved bits, defined, 1-5
Reset
considerations, 8-11
CPU-only, B-4
Resume instruction (RSM), 7-15
RSM, See Resume instruction
S
Scratch pad reg isters
SCRn, 11-32, D-56
Segment Descriptor Cache, 3-5
Segmentation Unit, 3-4, 3-5
SERCLK, 8-1–8-2, 11-1, 11-4, 11-21, 13-1,
13-5, 13-18
Serial I/O unit, 11-1–11-45
block diagram, 11-2
configuring, 5-14
departure from PC/AT architecture, B-3
DMA service, 5-3–5-5
operation, 11-4–11-14
baud-rate generator, 11-4–11-5
data transmission process flow, 11-8
diagnostic mode, 11-12
interrupt sources, 11-13
modem control, 11-12
receiver, 11-9–11-10
transmitter, 11-6–11-8
overview, 11-1–11-3
programming
accessing multiplexed registers, 11-16
considerations, 11-32
DLHn register, 11-22
DLLn register, 11-22
IERn register, 11-27
IIRn register, 11-28
LCRn, 11-25, D-36
LCRn register, 11-25
LSRn, 11-26, D-37
LSRn register, 11-26
MCRn,11-30, D-38
MCRn register, 11-29–11-30
modem control signals, 11-29–11-30
MSRn, 11-31, D-39
MSRn register, 11-31
P1CFG register, 11-18
P2CFG register, 11-19
P3CFG register, 11-20
PINCFG register, 11-17
RBRn, 11-24, D-52
RBRn register, 11-24
SCRn register, 11-32
SIOCFG, 5-17, 11-21, 13-18, D-57
SIOCFG register, 11-21
TBRn, 11-23, D-61
TBRn register, 11-23
register addresses, 4-19, 4-20, D-5, D-6
registers, 11-15–11-16
signals, 11-3
Set, defined, 1-5
Signal descriptions, A-1–A-10
Signal names, notational conventions, 1-4
SIO, See Serial I/O unit
SMM, See System management mode
SMM, see System Management Mode, 7-3
SMRAM, 7-2
chip-select unit support for, 7-12
state dump area, 7-14
Specific EOI command, 9-14
SSIO, See Synchronous serial I/O unit
Synchronous serial I/O unit, 13-1–13-25
configuring, 5-18
design considerations, 13-25
DMA service, 5-3
master/slave mode arrangements, 13-2–13-3