Manuals / JVC / TV and Video / DVD Recorder

JVC DR-M7S manual Basic Connections, A Install the unit, B Connect the unit to a TV

Models: DR-M7S

1 116

Download 116 pages 10.43 Kb

Page 18

INSTALLING YOUR NEW UNIT (cont.)

Filename [DR-M7EK_06Name.fm]
DR-M7EK_01.book Page 18 Friday, April 2, 2004 11:21 AM	Masterpage:Left+

18	INSTALLING YOUR NEW UNIT (cont.)

Basic Connections

Aerial connector

Back of TV

It’s essential that your unit be properly connected.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

A Install the unit.

Place the unit on a stable, horizontal surface.

TV aerial	RF cable
cable	(provided)

21-pin SCART connector

21-pin SCART cable (provided)

Mains power cord

ANTENNA IN

L-1 IN/OUT	Back of unit
L-1 IN/OUT	Mains outlet
ANTENNA OUT

ATTENTION:

Your TV must have a 21-pin AV input connector (SCART) for the connection to the unit.

B Connect the unit to a TV.

ADisconnect the TV aerial cable from the TV.

BConnect the TV aerial cable to the ANTENNA IN

connector on the rear panel of the unit.

CConnect the ANTENNA OUT connector on the rear panel of the unit and the TV’s aerial connector with

the provided RF cable.

DConnect the L-1 IN/OUT connector on the rear panel of the unit and the TV’s 21-pin SCART connector with

a provided 21-pin SCART cable.

●The L-1 IN/OUT connector accepts and delivers either a composite signal (regular video signal), Y/C signal or RGB signal.

●Select an appropriate option of “L-1 OUTPUT” as follows ( pg. 82):

	When your TV’s SCART	Set “L-1 OUTPUT” to:
	connector accepts:	Set “L-1 OUTPUT” to:
	connector accepts:

	Y/C signal (separated
	luminance (brightness) and	“SCART S-VIDEO”
	chrominance (colour) signals)

	RGB signal	“SCART RGB”

●Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to the type of your TV’s SCART connector.

●For switching the TV’s mode, refer to the instruction manual of your TV.

C Connect the unit to mains.

Connect the AC plug of the mains power cord into a mains outlet.

●“LOADING” blinks on the front display panel when the AC plug of the mains power cord is connected into a mains outlet, and it takes the unit approximately 50 seconds to be turned on. This is not a malfunction.

After connection is completed, perform “Auto Set Up” on page 21.

Page 18

April 2, 2004 11:21 am

Image 18

JVC DR-M7S manual Basic Connections, A Install the unit, B Connect the unit to a TV, C Connect the unit to mains

Contents

Filename DR-M7EK02Cov1.fm DVD VIDEO RECORDERINSTRUCTIONS DR-M7EK01.book Page 1 Friday, April 2, 2004 1121 AMSafety Precautions SAFETY FIRSTWARNING DANGEROUS VOLTAGE INSIDE 1. DO NOT place the unit MOISTURE CONDENSATION3. DO NOT place heavy objects on the unit or remote control 2. DO NOT block the unit’s ventilation openings or holesSAFETY FIRST cont Some Do’s And Don’ts On The Safe Use Of EquipmentABOVE ALL INSTALLING YOUR NEW UNIT CONTENTSSAFETY FIRST REMOTE CONTROLDISC INFORMATION About DiscsRecordable/playable discs DVD-RAM DiscsUnplayable Discs Discs for Playback OnlyRegion Number Examples of DVD VIDEO labels which can be played back using this unitDISC INFORMATION cont Recording Medium and FormatFile Structure of Discs DVD-RW VR modeRegarding the contents recorded on discs DVD VIDEO MarksMarks related to audio JPEG/MP3 Disc CD-R/RW/ROMHow to handle discs Placing a DiscCare and Handling of Discs Maintenance of discsFRONT VIEW INDEXD E FGH I J REAR VIEW INDEX contDisc Type/Status Indicator FRONT DISPLAY PANELA VPS/PDC Indicator* pg D Recording Mode Indicator XP/SP/LP/EP/FR pgH Linear PCM Indicator LPCM INDEX contG Simulated Surround Effect Indicator 3D pg I Random/Programme Playback Mode Indicator RND/PRGM pgON-SCREEN DISPLAY Page INSTALLING YOUR NEW UNIT Check ContentsCHECK ALL THE CONTENTS SHOWN BELOW 4 You are now ready to install your unit. pgBasic Connections A Install the unitINSTALLING YOUR NEW UNIT cont B Connect the unit to a TVB Connect the unit to mains S-VIDEO ConnectionA Connect the unit to a TV 8To connect to TV’s S-VIDEO input and AUDIO input connectorsINSTALLING YOUR NEW UNIT cont Component Video ConnectionA Connect the unit to TV 8To connect to TV’s component video input connectorsB Perform Auto Set Up Auto Set UpINITIAL SETTINGS Auto Channel Set/Auto Clock Set/ Auto Guide Program Number SetINITIAL SETTINGS cont After “Auto Set Up” is completed, perform “Monitor Set” on pageDVD F B Perform Preset DownloadENTER Preset DownloadINITIAL SETTINGS cont INFORMATIONJust Clock D Complete the setting A Access the Main Menu screenB Access the “VIDEO IN/OUT” screen Monitor SetB Access the “DISPLAY SET” screen ENTER SET UPB Access the “LANGUAGE SET” screen LanguageLanguage Code List MasterpageRight 3ColumnA Install a Satellite Controller Satellite Receiver Control SettingInstalling Satellite Controller B Attach the Satellite ControllerC Access the “SAT/GUIDE PR” screen Setting satellite receiver’s brand and channelB Access the Main Menu screen E Select the satellite receiver’s channel for testingUnit Auto Standby TV Auto Power OnT-V Link Functions Direct RecA Load a disc Basic PlaybackPLAYBACK OPERATIONS B Start playback1 Access the DVD menu Playback FeaturesLocating a desired scene using the DVD menu Locating the start point of the item or skip the itemHigh-Speed Search Slow MotionSkip Search Resume FunctionMarking positions to play again later Switching Time IndicationChecking the time information MARK1 Access Audio Language/Sound selection display 1 Access Angle display1 Access Subtitle display Subtitle SelectionAudio Channel Selection 1 Access the PBC menuLocating a desired scene using the menu of a Video CD/SVCD with PBC Playback Control PBC FunctionDISPLAY Live Memory PlaybackRecording/playback status display Image figure of DVD-RAM discDISPLAY Overview of Live Memory PlaybackLIVE CHECK PLAYBACK OPERATIONS contDisplay during Live Memory Playback Example of bar meter displayAvailable only when paused Buttons to be used during Live Memory PlaybackLIVE CHECK Available only when paused1 Start One Touch Replay function To play back from the beginning of the programme while recording1 Start Live Memory Playback To watch a programme previously recorded while recordingContents of Play Set Up Menu during playback DVD VIDEO Using Play Set Up MenuHow to Access Play Set Up Menu Before using Play Set Up Menu2 Select the menu item Basic operation on Play Set Up Menu1 Access Play Set Up Menu ON SCREENENTER CLEAR ON SCREEN 3 Select the repeat modeRepeat Playback 1 Access Play Set Up Menu3 Locate the start point selectionA-B Repeat Playback 4 Locate the end point and start A-B Repeat Playback1 Access Play Set Up Menu 3 Enter the time1 Access Play Set Up Menu To cancel the simulated surround effect3 Select the desired option Adjusting the picture qualitySetting the progressive mode 1 Access Play Set Up MenuRandom Playback Select the switching interval of the slide showProgramme Playback 3 Select the tracks in the desired orderD Enter your password SET UPB Access the “PARENTAL LOCK” screen Enter your passwordA Access the password screen To change the settingsC Enter your password B Enter your passwordCountry/Area Code List for Parental Lock Italy Jamaica Jordan Japan Kenya Kyrgyzstan Cambodia Kiribati ComorosPLAYBACK OPERATIONS cont DR-M7EK01.book Page 52 Friday, April 2, 2004 1121 AMRECORDING 4 REC MODEBasic Recording C Set the recording speed2 Engage the ITR mode Recording FeaturesInstant Timer Recording ITR 1 Switch the TV to TV modeSelection of the audio channel to be recorded on a disc Free Rate FunctionReceiving Stereo and Bilingual Programmes To record the entire programme within the actual remaining disc spaceTIMER RECORDING VIDEO Plus+ Timer ProgrammingB Access the VIDEO Plus+ screen C Enter the PlusCode numberH Engage the unit’s timer mode F Access the confirmation screenG Complete timer programming E Set the following recording options as requiredC Access the programme screen Manual Timer ProgrammingB Access Programme Check screen TIMER RECORDING contK Engage the unit’s timer mode I Access the confirmation screenJ Complete timer programming PDC RecordingPROG/CHECK On-Disc Timer ProgrammingTo make the disc for On-Disc Timer Programming B Access Programme Check screenK Complete timer programming To timer-record the programme with the programmed discJ Access the confirmation screen B Engage the unit’s timer modeHow discs are overwritten TIMER RECORDING contComplete timer correction Check, cancel and change programmesAccess the programme screen Engage the unit’s timer modeC Change the programme setting When programmes overlap each otherB Select the desired programme to be cancelled or changed E Engage the unit’s timer modeREC MODE A Select the L-2 SELECT modeRecording mode Programme RecordingLibrary Database DVD Navi NAVIGATIONThe Icons and their meanings About registration of information The display for original recording The display for play listThe display for library About editing of programmesCLEAR C Access the Index screenScan for Beginnings of Programmes B Load a discModify Original Information B Access the Index screenD Access the modify screen Modify IndexModify Category A Access the modify screenModify Programme Name Protect titleDelete unwanted part of the programme B Access the delete screenDelete programme D Set edit-in and edit-out pointsCreate Play List C Access the Play List screenModify Play List Information D Create a play listMove scenes B Access the Editing screenAdd scenes to a play list H Return to the normal screenB Access the Editing screen Delete unwanted part from play listE Confirm the move D Set edit-in and edit-out pointsDelete play list Play back play listModify Programme Title A Select the play listsScan for Programme from library Access the library screenModify Library Information C Sort the informationRegister disc B Access the library screenC Access the library screen Delete informationPlayback with MP3/JPEG Navigation NAVIGATION contC Display the item B Access the MP3/JPEG Navigation screenLocating the desired group and tracks D Select the groupA Make connections B Set the unit’s input modeEdit From A Camcorder E Start dubbingD Start the source player B Set the input mode of recording deckEdit To Or From Another Recorder E Start the recording deckC Select the output or input mode for the L-1 IN/OUT connector L-1 Output and L-1 Input Setting L-1 OUTPUT and L-1 INPUTB Access the Output/Input Set screen SET UPA Select the input mode for the L-2 IN DECODER connector F-1 Input Setting F-1 INPUTL-2 Select Setting L-2 SELECT A Select the input mode for the VIDEO S-VIDEO connectorC Prepare the unit for dubbing Digital Audio DubbingB Place a disc and load an MD D Prepare the digital audio device for dubbingREMOTE CONTROL Remote Control FunctionsRemote 1/2/3/4 Code Switching A Change the remote control codeTV % TV Multi-Brand Remote ControlREMOTE CONTROL cont A Set the TV brand codeB Operate the satellite receiver Satellite Receiver Multi-Brand Remote ControlA Set the satellite receiver brand code SET UPSatellite receiver Connecting To A Satellite ReceiverSYSTEM CONNECTIONS Back of unitMake connections CAUTIONSWhen you can’t switch the audio channel of a bilingual programme SUBSIDIARY SETTINGS Mode SetB Access the “RECORDING SET” screen SET UP8 ANALOG AUDIO OUT AUDIO OUTPUT8 DIGITAL AUDIO OUT 8 D. RANGE CONTROLRECORDING SET SUBSIDIARY SETTINGS cont8 XP MODE REC AUDIO 8 SAVE AS LIBRARY8 SUPERIMPOSE 8 POWER SAVEDISPLAY SET 8 GREY BACK8 RESUME 8 AUTO TIMEROTHERS SUBSIDIARY SETTINGS contB Access the “SAT/GUIDE PR” screen VIDEO Plus+ System SetupE Complete the setting Guide Program Number SetB Perform Auto Channel Set Tuner SetAuto Channel Set C View the Confirmation screenC Select the channel position B Access the Confirmation screenManual Channel Set SET UPD Select the band Delete A ChannelChange Station Channel Position A Select the itemPerform fine-tuning Fine-Tuning Channels Already StoredSwitch the stations Set Stations ASTATION NAME TV Station And ID ListSUBSIDIARY SETTINGS cont STATION NAMENorth-West TV Station Channel Number GuideLondon & South-East North-EastC Set the date and time B Access the “CLOCK SET” screenClock Set SET UPF Start the clock operation D Set Just ClockE Set the source channel position for clock data ENTERFormat a DVD-RAM disc B Access the “UTILITY” screenFormat A Disc Format a DVD-RW discFinalise A Disc Cancel the finalisation of a DVD-RW discA Cancel the disc finalisation Finalise a DVD-R/RW discTray Lock Scan Mode SetA Set the scan mode A Lock the disc trayGENERAL TROUBLESHOOTINGSYMPTOM PLAYBACKINITIALIZING TROUBLESHOOTING contRECORDING SYMPTOMON-SCREEN MESSAGES MESSAGEDESCRIPTION Timer recording finished during Live Memory playback, then the ON-SCREEN MESSAGES contTROUBLESHOOTING cont next timer recording is about to begin while playback continues8Component video signal GLOSSARY8Composite video signal 8PAL Phase Alternation by LineACCESSORIES SPECIFICATIONSTUNER/TIMER GENERALLIST OF TERMS MEMO DR-M7EK01.book Page 114 Friday, April 2, 2004 1121 AMMasterpageLeft MEMO DR-M7EK01.book Page 115 Friday, April 2, 2004 1121 AMMasterpageRight DR-M7S DR-M7EK01.book Page 116 Friday, April 2, 2004 1121 AMPrinted in Germany 0404MNH-ID-VE