96 |
| TROUBLESHOOTING (cont.) | |
TIMER RECORDING (cont.) |
| ||
|
|
|
|
| SYMPTOM | POSSIBLE CAUSE | CORRECTIVE ACTION |
5. | “#” blinks for 10 seconds and the | ● # has been pressed when there are | Check the programmed data and re- |
| Timer mode is disengaged. | no programs in memory. | program as necessary, then press # |
|
|
| again. |
|
|
|
|
6. | The VIDEO PLUS+ system does not | ● The recorder’s channel positions | Refer to “Guide Program Number |
| have been set incorrectly. | Set” ( pg. 83) and | |
|
|
| procedure. |
|
|
|
|
7. | “” and “$” on the front display | ● The end of the tape was reached | The programme may not have been |
| panel won’t stop blinking. | during Instant Timer Recording. | recorded in its entirety. Next time |
|
|
| make sure you have enough time on |
|
|
| the tape to record the entire |
|
|
| programme. |
|
|
|
|
8. | “N”, “” and “$” on the front | ● The loaded cassette has had its | Remove the cassette and cover the |
| display panel won’t stop blinking. | record safety tab removed. | hole with adhesive tape, or insert a |
|
|
| cassette with the record safety tab |
|
|
| intact. |
|
| ● The end of the tape was reached | The programme may not have been |
|
| during Automatic Satellite | recorded in its entirety. Next time |
|
| Programme Recording. | make sure you have enough time on |
|
|
| the tape to record the entire |
|
|
| programme. |
|
|
| |
OTHER PROBLEMS |
|
| |
|
|
|
|
| SYMPTOM | POSSIBLE CAUSE | CORRECTIVE ACTION |
1. | Whistling or howling is heard from | ● The camcorder’s microphone is too | Position the camcorder so its |
| the TV during camcorder | close to the TV. | microphone is away from the TV. |
| recording. | ● The TV’s volume is too high. | Turn the TV’s volume down. |
|
| ||
|
|
|
|
2. | When scanning channels, some of | ● Those channels have been | If you need the skipped channels, |
| them are skipped over. | designated to be skipped. | restore them ( pg. 88). |
|
|
|
|
3. | The channel cannot be changed. | ● Recording is in progress. | Press 9 to pause the recording, |
|
|
| change channels, then press 4 to |
|
|
| resume recording. |
|
|
|
|
4. | Channel settings that were made | ● After the manual settings were | Perform manual setting again. |
| manually seem to have changed or | made, Auto Channel Set was |
|
| disappeared. | performed. |
|
|
|
|
|
5. | No channels are stored in the | ● The TV aerial cable was not | Turn off the recorder once and |
| recorder’s memory. | connected to the recorder when | connect the TV aerial cable to the |
|
| Auto Set Up was performed. | recorder properly, then turn on the |
|
|
| recorder again. Then perform Auto |
|
|
| Set Up again. ( pg. 14) |
|
| ● The | Turn off the recorder once and |
|
| was not connected between TV and | connect the |
|
| the recorder when Preset | SCART cable to the recorder properly, |
|
| Download was performed. | then turn on the recorder again. Then |
|
|
| perform Preset Download again. |
|
|
| ( pg. 16) |
|
|
|
|
6. | The remote control won’t operate | ● The remote control brand setting is | |
| the TV or satellite receiver. | incorrect. | correct brand. ( pg. 53, 54) |
|
|
|
|
7. | A programme that has a title | ● The power was cut off because of a | Delete the “Found 001” programme. |
| “Found 001” is recorded | power failure, etc. while the | ( pg. 58) |
| unexpectedly on the HDD deck. | recorder was working. |
|
|
|
|
|