EDITING

Output/Input Set

●Turn on the unit.

●Turn on the TV and select an input mode such as EXT1.

●Set the remote control selector switch to AUDIO.

●Press DVD on the remote control.

DVD

1

2

3

 

4

5

6

AUDIO

 

 

 

TV

7

8

9

SAT

 

0

 

 

 

SETTING

VOL

Selection Keys

(FGDE)

ENTER

SET UP

L-1 Output And L-1 Input Setting

The [L-1 INPUT/OUTPUT] connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set AL-1 OUTPUTB and AL-1 INPUTB to the appropriate mode depending on the type of appliance connected to the unit’s [L-1 INPUT/ OUTPUT] connector.

1Press SET UP to access the Main Menu screen.

2Press selection keys to select AFUNCTION SET UPB, then press ENTER.

* The boldface settings below indicate the settings at your purchase.

8L-1 OUTPUT ^ SCART VIDEO / SCART S-VIDEO /SCART RGB / COMPONENT
SCART VIDEO:

If a connected appliance’s input is compatible only with regular video signals, set to ASCART VIDEOB.

SCART S-VIDEO:

If a connected appliance’s input is compatible with Y/C signals, set to ASCART S-VIDEOB. You can obtain a high quality picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

SCART RGB:

If a connected appliance’s input is compatible with RGB signals, set to ASCART RGBB. You can obtain a high quality RGB picture.

COMPONENT:

If a connected appliance’s input is compatible with Y/PB/PR signals, set to ACOMPONENTB. You can obtain a high quality Y/PB/PR picture. Switch the TV to the input that you can watch component video pictures.

8L-1 INPUT ^ VIDEO / S-VIDEOVIDEO:

If a connected appliance’s output is compatible only with regular video signals, set to AVIDEOB.

S-VIDEO:

If a connected appliance’s output is compatible with Y/C signals, set to AS-VIDEOB. You can obtain a high quality picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

NOTES:

●If AL-1 OUTPUTB is set to ASCART S-VIDEOBor ASCART RGBB, it is not possible to set AL-1 INPUTB to AS-VIDEOB.

●If AL-2 SELECTB is set to ASAT S-VIDEO/RGBBor ADECODERB, it is not possible to set AL-1 INPUTB to AS-VIDEOB.

●If AL-2 SELECTB is set to ADECODERB, it is only possible to set AL-1 OUTPUTB to ASCART VIDEOB or ACOMPONENTB.

●Component video signals are not output from the [L-1 INPUT/ OUTPUT] connector.

●When Progressive scan mode is engaged, it is not possible to select the setting of AL-1 OUTPUTB on the left column.

L-1 And L-2 Audio Input Setting

3Press selection keys to select AVIDEO IN/ OUTB, then press ENTER for confirmation.

4Press selection keys to select AL-1 OUTPUTB or AL-1 INPUTB, then press

ENTER.

DVD SET UP

FUNCTION SET UP INITIAL SET UP

VIDEO IN/OUT

RECORDING SET

DISPLAY SET

OTHERS

MONITOR TYPE

4:3LB

 

F-1 INPUT

VIDEO

 

L-1 INPUT

VIDEO

 

L-1 OUTPUT

SCART VIDEO

L-2 SELECT

S-VIDEO/RGB

SET UP

OK

SELECT WITH [CURSORS]

 

 

EXIT

SELECT

THEN PRESS [ENTER]

 

 

You can select to input audio signals through the coaxial digital/ optical [L-1/L-2 DIGITAL INPUT (COAXIAL/OPTICAL)] or analogue connectors depending on the appliance connected to the unit. There is a time limit when performing the following setting. If the time is up before completing the setting, re-perform from the beginning.

1

Press SETTING.

 

The item of the setting performed most recently is displayed on

2

the front display panel.
Press F or G to display the L-1,L-2input setting on the front

5Press selection keys

to select the appropriate setting, then press ENTER.

6Press SET UP to complete the setting.

\

display panel.
3 Press D or E to select the desired audio input.
Each time you press D or E, the L-1and L-2combination is
displayed in the sequence as shown below:
L-1L-2

(AN - AN) N (AN - OP) N (AN - CO) N (OP - AN) N (OP - CO) N (CO - AN) N (CO - OP) N (back to the beginning)

AN: Analogue signal input
OP: Optical signal input
CO: Coaxial digital signal input

69