Manual Timer Programming
You can programme this unit to timer record as many as8 programmes up to 30 days in advance. If you do not know the SHOWVIEW number for the programme you wish to record, use the following procedure to set your unit to timer record the programme.
●Turn on the unit.
●Turn on the TV and select an input mode such as EXT1.
●Set the remote control selector switch to AUDIO.
●Press DVD on the remote control.
●Make sure that the unit’s
TIMER j
DVD
PROG | 1 | 2 | 3 |
| |
4 | 5 | 6 | AUDIO | ||
| |||||
|
|
|
| TV | |
| 7 | 8 | 9 | SAT | |
|
| 0 |
|
| |
|
|
| VOL | Selection Keys |
(FGDE)
ENTER
DISPLAY
1Load a recordable disc.
●To programme another timer, repeat steps 2 - 10.
11 Press TIMERj to engage the unit’s timer mode.●The unit turns off automatically and j appears on the front display panel.
●To disengage the timer mode, press TIMERj again.
●TV DIRECT mode is activated when the unit turns on automatically during timer recording.
●When two successive programmes are recorded with the
AManual Timer ProgrammingB function, the ending of the first programme or the beginning of the second programme may not be recorded.
●If the copy limited programme is received during timer recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed.
Satellite Receiver UsersTo record a satellite broadcast using Manual Timer Programming:APerform Manual Timer Programming.BSet the satellite receiver to the appropriate channel for recording.●Leave the satellite receiver’s power on.VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are services designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the
●When APROGRAMME FULL DELETE UNWANTED TIMER PROGRAMMEB appears on the TV screen, you need to cancel some of the reserved programmes.
PROGRAMME CHECK
DATE | TV PROG | DAILY/WEEKLY | VPS/PDC | REC MODE | |
05/07 SAT | 19:00 - 20:00 | 44 | WEEKLY | ON | SP |
10/07 THU | 22:00 - 22:30 | 10 |
| ON | XP |
11/07 FRI | 13:30 - 14:00 | 26 |
| OFF | LP |
11/07 FRI | 16:00 - 17:00 | 33 |
| OFF | LP |
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
DISC TIMER PRGM
EXIT OK
PROG
audio/video signals. These code signals control your unit and have precedence over the advertised times you may have preset into the timer. This means that your unit will start and stop recording when the preset TV programmes actually start and end^even if the broadcast time of a preset TV programme is changed.
●When you use Manual Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.
●VPS/PDC recording is also possible via the3
4
Press selection keys to set the desired date (ADATEB), then press E.
TIMER PROGRAMME
|
|
|
|
DATE | START | STOP | TV PROG |
05/07 SAT | 20:00 | 20:30 | VTM 10 |
DAILY/WEEKLY | VPS/PDC | REC MODE | NAME |
|
|
| |
|
|
|
|
APress DISPLAY for 5 or more seconds. AVPS/PDCB is displayed on the front display panel. If a VPS/PDC signal is detected from the station, AVPS/PDCB will stop blinking. If no VPS/PDC signal is detected from the station, AVPS/PDCB will blink at a slower rate.
BPress DISPLAY again to return to normal display.5 Press selection keys to | EXIT | CONFIRM SET TIMER PROGRAMMING WITH [CURSORS] | |
PROG | SELECT | THEN PRESS [ENTER] | |
set the desired start |
| ||
|
|
|
50