Service Views, 1214 | Kohler 8/10/12RESVL specification

1.9 Service Views

1

13

15

1214

2

11

10

9

8

7

6

5

4

3

16

17

18

19

ADV-8539

1.Hinged roof

2.Air cleaner

3.Nameplate location

4.Thermostat

5.Engine starting battery location (battery purchased separately)

6.Gas regulator assembly and fuel selector valve

7.Fuel solenoid valve

8.Fuel inlet

9.Field-connection terminal block and 20 amp resettable circuit breaker (behind panel)

10.Line circuit breaker

11.120 VAC receptacles for optional carburetor heater (not shown)

12.Lock

13.Locking tool, provided with generator set

14.USB port

15.RDC2 or DC2 controller

16.Oil check (dipstick) and oil fill

17.Oil drain valve

18.Oil filter

19.Muffler

Figure 1-2Service View

TP-6880 10/14

Section 1 Descriptions and Service Views 17

Image 17

Kohler 8/10/12RESVL manual Service Views, 1214

Contents

TP-6880 10/14a RDC2 Product Identification Information Accessory Number Accessory DescriptionGenerator Set Identification Numbers Controller Identification Table of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Battery Safety Precautions and InstructionsAccidental Starting Accidental starting Can cause severe injury or death Exhaust System Engine Backfire/Flash FireCarbon monoxide Can Cause Fire Can cause severe injury or death Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment Accessory Literature Transfer Switch LiteratureIntroduction List of Related Literature Emission Information NameplateGenerator Set Application Emission Compliance Period Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Carburetor Heater AccessoriesProgrammable Interface Module PIM Load Control Module LCM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Setting the Exerciser Automatic Operation with Other Transfer SwitchesUnloaded Cycle Exercise with Complete System Diagnostics Exercise System Diagnostics Power Failure During Exercise CycleUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT only ATS Communication Errors FaultsResetting the Controller after a Fault Shutdown Shutdowns Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators Button Controller Keypad LED IndicatorsButton Function LED Operation Active Alert LCD Display Battery Charging Controller PowerChanging Settings Procedure to Change Settings 7Changing Settings Changing Settings on the RDC2 Controller Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Adjusting the Display Contrast Setting the ExerciserGenset System Menu Voltage Regulator VR Voltage Adj Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Dhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Button Button Function Controller KeypadLED Indication Description 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Lubrication System Oil Change ProcedureEngine Oil Recommendation Low Oil Pressure Shutdown Drain the oil Reset the maintenance timer on the controllerReplace the oil filter Fill with oil Spark Plugs Resetting the Maintenance TimerModel Resv RDC2 Model Resvl DC2 Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Fault Messages TroubleshootingIntroduction USB Port Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14