RDC2 Controller Menus, Main Menu | Kohler 8/10/12RESVL instruction

3.7 RDC2 Controller Menus

Controller menus display power system information, including status information for the engine, generator, and optional RBUS accessories, exercise settings, and event history. Some menus allow changes to the controller settings. Status information, including the engine runtime, cannot be changed by the operator.

Diagrams in the following sections show how to navigate through the menus.

Note: Use caution when navigating the controller menus. In some menus, pressing the Select button can enable editing of the controller settings. Changing the settings to incorrect values can adversely affect generator set operation or render the unit inoperable.

If a setting on the controller display is flashing, edit mode has been enabled. Press the OFF or AUTO button to exit the edit mode.

3.8 Main Menu

Press the Select button once to bring up the main menu. Overview is displayed. See Figure 3-9. Press the down arrow button to step to the next menu, Engine Metering. Use the UP and DOWN arrow buttons to step up and down through the menus shown in Figure 3-9.

The controller will exit the main menu after 5 minutes if no buttons are pressed. To exit the main menu immediately, press the controller’s OFF or AUTO button.

Status	Overview ---->
Displays	1.2 h

Press the Up and Down arrow buttons to move between menus.

Press OFF or AUTO to exit the menus.

Engine ---->

Metering

Generator---->

Metering

ATS ---->

Configuration *

Date ---->

and Time

Genset	---->
Information
Genset	---->
Run Time
Genset	---->
System
ATS	---->
Status

*ATS Configuration appears only if a Model RXT transfer switch is connected. [ PIM Status appears only if a programmable interface module is connected.

] Load Control appears only if a load control module (LCM) or load shed kit is connected.

Network ---->

Information

PIM ---->

Status [

Load ---->

Control ]

Event Log---->

tp6804

Figure 3-9RDC2 Main Menu

36 Section 3 RDC2 Controller Operation

TP-6880 10/14

Image 36

Kohler 8/10/12RESVL manual RDC2 Controller Menus, Main Menu

Contents

RDC2 TP-6880 10/14a Accessory Number Accessory Description Product Identification InformationGenerator Set Identification Numbers Controller Identification Table of Contents Scheduled Maintenance TroubleshootingDC2 Controller Operation Safety Precautions and Instructions BatteryAccidental Starting Accidental starting Can cause severe injury or death Engine Backfire/Flash Fire Exhaust SystemCarbon monoxide Can Cause Fire Can cause severe injury or death Fuel System Hazardous Noise Hazardous voltage Will cause severe injury or death Heavy Equipment Hot Parts Transfer Switch Literature Accessory LiteratureIntroduction List of Related Literature Nameplate Emission InformationGenerator Set Application Emission Compliance Period Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Accessories Carburetor HeaterProgrammable Interface Module PIM Load Control Module LCM Service Views 1214 3Service View Prestart Checklist Generator Set Operation Generator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set Operation Automatic Operation with Other Transfer Switches Setting the ExerciserUnloaded Cycle Exercise with Complete System Diagnostics Exercise Power Failure During Exercise Cycle System DiagnosticsUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT only Faults ATS Communication ErrorsResetting the Controller after a Fault Shutdown Shutdowns Fault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition Check Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Generator Set/ Transfer Switch Controller Controls and IndicatorsRDC2 Controller Operation Controller Keypad LED Indicators ButtonButton Function LED Operation LCD Display Active Alert Controller Power Battery ChargingChanging Settings Procedure to Change Settings Changing Settings on the RDC2 Controller 7Changing Settings Setting the Exerciser Setting the Exerciser at Controller Power-upChanging the Exercise Settings Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main Menu Overview Menu Engine Metering Menu Generator Metering Menu Voltage Calibration Generator Set Information Menu Genset Run Time Menu Setting the Exerciser Adjusting the Display ContrastGenset System Menu Voltage Regulator VR Voltage Adj ATS Status Menu Screens on this page do not appear ATS Configuration Menu Changing ATS Configuration Settings Date and Time Menu Networking Information Menus Networking Status Submenu Dhcp Networking Configuration Submenu OnCue Plus Password PasswordDhcp Submenu 21Network Configuration Submenu Rbus Information 22RBUS Information Submenu Remote Devices Submenu From Figure Programmable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status Menu Procedure to View Event History Event Log RDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller Operation Controller Keypad Button Button FunctionLED Indication Description 5Status Displays, Generator Running Exerciser Reset Exercise Modes Maintenance Timer OnCue Plus Password DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Oil Change Procedure Lubrication SystemEngine Oil Recommendation Low Oil Pressure Shutdown Reset the maintenance timer on the controller Drain the oilReplace the oil filter Fill with oil Resetting the Maintenance Timer Spark PlugsModel Resv RDC2 Model Resvl DC2 Air Cleaner Service Air Cleaner, 8RESV/RESVL ModelsPaper Element Service Air Cleaner, 10/12RESV/RESVL Models Cooling System Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Troubleshooting Fault MessagesIntroduction USB Port Troubleshooting Problem Possible Cause Corrective Action Appendix a Abbreviations Ansi LCB Page TP-6880 10/14