5Status Displays, Generator Running | Kohler 8/10/12RESVL manual

4.2.3LCD Display

The controller is equipped with a two-line x 16 character backlit digital display with adjustable contrast. When the generator set is running, the messages shown in Figure 4-5 are displayed. When the system is in AUTO, the LCD display steps through the status messages shown in Figure 4-6.

When a fault or warning condition exists, the controller will show the corresponding message. See Section 2.5 for more information on fault and warning messages.

The display backlight turns off after about a minute of no activity. The backlight turns on when a button is pressed or when the generator set starts.

Active Alert (if any)

Running

ATS: Normal *

Voltage: 240V

Freq: 60.0Hz

Engine: 123F

Oil Pressure: OK

Battery 12.3V

Runtime: 12345.6 h

Next Exercise: 7d 6h 42m

OnCue Status:

Disconnected [

Sample data shown.

* Model RXT ATS required

[ OnCue status is displayed only if OnCue password has been reset.

Figure 4-5Status Displays, Generator Running

Active Alert (if any)

Genset State

Standby

Battery 12.3V

Runtime: 12345.6 h

Next Exercise: 7d 6h 42m

Next Maint:

123h or 12months

OnCue Status:

Disconnected

Sample data shown.

[ OnCue status is displayed only if OnCue password has been reset.

Figure 4-6Status Displays, Generator in Standby

4.3 Controller Power

The DC2 controller is powered by the generator set engine starting battery.

Note: To disconnect controller power, disconnect the utility power to the generator set and disconnect the battery (negative lead first).

4.4 Battery Charging

The controller includes a built-in battery charger to maintain the engine starting battery. The DC2 controller monitors the battery voltage and provides a constant 14 ±2% VDC voltage and maximum 2.5 amps to charge the battery.

The installer must connect 120 VAC/60Hz utility power provided from the building on a breaker-protected circuit for the built-in battery charger. See the Installation Manual for instructions to connect power.

TP-6880 10/14

Section 4 DC2 Controller Operation 55

Image 55

Kohler 8/10/12RESVL manual 5Status Displays, Generator Running

Contents

TP-6880 10/14a RDC2 Controller Identification Accessory Number Accessory DescriptionProduct Identification Information Generator Set Identification Numbers Table of Contents Troubleshooting Scheduled MaintenanceDC2 Controller Operation Accidental starting Can cause severe injury or death Safety Precautions and InstructionsBattery Accidental Starting Fire Can cause severe injury or death Engine Backfire/Flash FireExhaust System Carbon monoxide Can Cause Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment List of Related Literature Transfer Switch LiteratureAccessory Literature Introduction Emission Compliance Period NameplateEmission Information Generator Set Application Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Load Control Module LCM AccessoriesCarburetor Heater Programmable Interface Module PIM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Exercise Automatic Operation with Other Transfer SwitchesSetting the Exerciser Unloaded Cycle Exercise with Complete System Diagnostics Loaded Full-Speed Exercise with RXT only Power Failure During Exercise CycleSystem Diagnostics Unloaded Full-Speed Exercise Shutdowns FaultsATS Communication Errors Resetting the Controller after a Fault Shutdown Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 Controls and Indicators RDC2 Generator Set/ Transfer Switch ControllerRDC2 Controller Operation LED Operation Controller Keypad LED IndicatorsButton Button Function Active Alert LCD Display Procedure to Change Settings Controller PowerBattery Charging Changing Settings 7Changing Settings Changing Settings on the RDC2 Controller Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Voltage Regulator VR Voltage Adj Setting the ExerciserAdjusting the Display Contrast Genset System Menu Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Password Networking Configuration Submenu OnCue Plus PasswordDhcp Submenu 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Description Controller KeypadButton Button Function LED Indication 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Low Oil Pressure Shutdown Oil Change ProcedureLubrication System Engine Oil Recommendation Fill with oil Reset the maintenance timer on the controllerDrain the oil Replace the oil filter Model Resvl DC2 Resetting the Maintenance TimerSpark Plugs Model Resv RDC2 Air Cleaner, 8RESV/RESVL Models Air Cleaner ServicePaper Element Service Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 USB Port TroubleshootingFault Messages Introduction Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14