Generator Metering Menu, Voltage Calibration | Kohler 8/10/12RESV

3.11 Generator Metering Menu

The generator metering menu displays the generator voltage and frequency. See Figure 3-12.

Voltage Calibration

DANGER

Hazardous voltage.

Will cause severe injury or death.

This equipment must be installed and serviced by qualified electrical personnel.

The voltage calibration mode can be entered from the Generator Metering menu. Contact a Kohler-authorized distributor/dealer for service.

The Reset Calibration menu allows you to set the voltage reading back to the original value after calibration, if necessary. See Figure 3-12.

Generator ---->
Metering
Three-phase	Single-phase
Three-phase
Volts L1--L2:	Volts:	Note: Actual settings may vary.
240 V		240 V
Volts L2--L3:	Frequency:
240 V		60.0 Hz
Volts L3--L1:
240 V
Frequency:
60.0 Hz
	Reset	Reset
	Calibration	Calib? No
	<---- Return	Reset
	<---- Return	Calib? Yes
		Calib? Yes

tp6810

Figure 3-12Generator Metering Menu

38 Section 3 RDC2 Controller Operation

TP-6880 10/14

Image 38

Kohler 8/10/12RESVL manual Generator Metering Menu, Voltage Calibration

Contents

RDC2 TP-6880 10/14a Generator Set Identification Numbers Accessory Number Accessory DescriptionProduct Identification Information Controller Identification Table of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Accidental Starting Safety Precautions and InstructionsBattery Accidental starting Can cause severe injury or death Carbon monoxide Can Cause Engine Backfire/Flash FireExhaust System Fire Can cause severe injury or death Fuel System Hazardous Noise Hazardous voltage Will cause severe injury or death Heavy Equipment Hot Parts Introduction Transfer Switch LiteratureAccessory Literature List of Related Literature Generator Set Application NameplateEmission Information Emission Compliance Period Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Programmable Interface Module PIM AccessoriesCarburetor Heater Load Control Module LCM Service Views 1214 3Service View Prestart Checklist Generator Set Operation Generator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set Operation Unloaded Cycle Exercise with Complete System Diagnostics Automatic Operation with Other Transfer SwitchesSetting the Exerciser Exercise Unloaded Full-Speed Exercise Power Failure During Exercise CycleSystem Diagnostics Loaded Full-Speed Exercise with RXT only Resetting the Controller after a Fault Shutdown FaultsATS Communication Errors Shutdowns Fault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition Check Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators Button Function Controller Keypad LED IndicatorsButton LED Operation LCD Display Active Alert Changing Settings Controller PowerBattery Charging Procedure to Change Settings Changing Settings on the RDC2 Controller 7Changing Settings Changing the Exercise Settings Setting the ExerciserSetting the Exerciser at Controller Power-up Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main Menu Overview Menu Engine Metering Menu Generator Metering Menu Voltage Calibration Generator Set Information Menu Genset Run Time Menu Genset System Menu Setting the ExerciserAdjusting the Display Contrast Voltage Regulator VR Voltage Adj ATS Status Menu Screens on this page do not appear ATS Configuration Menu Changing ATS Configuration Settings Date and Time Menu Networking Information Menus Networking Status Submenu Dhcp Dhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu Rbus Information 22RBUS Information Submenu Remote Devices Submenu From Figure Programmable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status Menu Procedure to View Event History Event Log RDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller Operation LED Indication Controller KeypadButton Button Function Description 5Status Displays, Generator Running Exerciser Reset Exercise Modes Maintenance Timer OnCue Plus Password DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Engine Oil Recommendation Oil Change ProcedureLubrication System Low Oil Pressure Shutdown Replace the oil filter Reset the maintenance timer on the controllerDrain the oil Fill with oil Model Resv RDC2 Resetting the Maintenance TimerSpark Plugs Model Resvl DC2 Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Air Cleaner, 10/12RESV/RESVL Models Cooling System Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Introduction TroubleshootingFault Messages USB Port Troubleshooting Problem Possible Cause Corrective Action Appendix a Abbreviations Ansi LCB Page TP-6880 10/14