Networking Status Submenu, Dhcp | Kohler 8/10/12RESVL guide

3.18.1 Networking Status Submenu

The Networking Status submenu contains settings for OnCuer Plus. See the OnCue Plus Software Operation Manual for information about the appropriate network settings for OnCue Plus. Changes to these settings are not typically required.

If DHCP is enabled, IP parameters are not displayed. If DHCP is disabled (i.e., if a static IP address is used), the IP parameters are displayed.

To enable or disable DHCP and change the IP settings, go to the Networking Configuration menu. See Section 3.18.2.

Networking---->

Information

Networking---->

Status

OnCue Status: Connected

DHCP:

Enabled

IP Address: 123.456.789.123

Subnet Mask: 123.456.789.123

Gateway:

123.456.789.123

DNS 1: 123.456.789.123

DNS 2: 123.456.789.123

Ethernet Status:

Disconnected

OnCue Server: 123.456.789.123

<---- Return

tp6804

Figure 3-20Network Status Submenu

44 Section 3 RDC2 Controller Operation

TP-6880 10/14

Image 44

Kohler 8/10/12RESVL manual Networking Status Submenu, Dhcp

Contents

RDC2 TP-6880 10/14a Accessory Number Accessory Description Product Identification InformationGenerator Set Identification Numbers Controller Identification Table of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Safety Precautions and Instructions BatteryAccidental Starting Accidental starting Can cause severe injury or death Engine Backfire/Flash Fire Exhaust SystemCarbon monoxide Can Cause Fire Can cause severe injury or death Fuel System Hazardous Noise Hazardous voltage Will cause severe injury or death Heavy Equipment Hot Parts Transfer Switch Literature Accessory LiteratureIntroduction List of Related Literature Nameplate Emission InformationGenerator Set Application Emission Compliance Period Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Accessories Carburetor HeaterProgrammable Interface Module PIM Load Control Module LCM Service Views 1214 3Service View Prestart Checklist Generator Set Operation Generator Set Operation TP-6880 10/14 Exercising the Generator Set Generator Set Operation Automatic Operation with Other Transfer Switches Setting the ExerciserUnloaded Cycle Exercise with Complete System Diagnostics Exercise Power Failure During Exercise Cycle System DiagnosticsUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT only Faults ATS Communication ErrorsResetting the Controller after a Fault Shutdown Shutdowns Fault Message Shutdown SD Condition Check 3Controller Fault Messages Fault Shutdown SD Condition Check Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators Controller Keypad LED Indicators ButtonButton Function LED Operation LCD Display Active Alert Controller Power Battery ChargingChanging Settings Procedure to Change Settings Changing Settings on the RDC2 Controller 7Changing Settings Setting the Exerciser Setting the Exerciser at Controller Power-upChanging the Exercise Settings Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the RDC2 Controller RDC2 Controller Menus Main Menu Overview Menu Engine Metering Menu Generator Metering Menu Voltage Calibration Generator Set Information Menu Genset Run Time Menu Setting the Exerciser Adjusting the Display ContrastGenset System Menu Voltage Regulator VR Voltage Adj ATS Status Menu Screens on this page do not appear ATS Configuration Menu Changing ATS Configuration Settings Date and Time Menu Networking Information Menus Networking Status Submenu Dhcp Dhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu Rbus Information 22RBUS Information Submenu Remote Devices Submenu From Figure Programmable Interface Module PIM Status Menu Load Control Module LCM or Load Shed Kit Menus 25Load Control Module LCM or Load Shed Kit Status Menu Procedure to View Event History Event Log RDC2 Controller Operation TP-6880 10/14 DC2 Generator Set/ Transfer Switch Controller DC2 Controller Operation Controller Keypad Button Button FunctionLED Indication Description 5Status Displays, Generator Running Exerciser Reset Exercise Modes Maintenance Timer OnCue Plus Password DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Oil Change Procedure Lubrication SystemEngine Oil Recommendation Low Oil Pressure Shutdown Reset the maintenance timer on the controller Drain the oilReplace the oil filter Fill with oil Resetting the Maintenance Timer Spark PlugsModel Resv RDC2 Model Resvl DC2 Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Air Cleaner, 10/12RESV/RESVL Models Cooling System Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Troubleshooting Fault MessagesIntroduction USB Port Troubleshooting Problem Possible Cause Corrective Action Appendix a Abbreviations Ansi LCB Page TP-6880 10/14