Date and Time Menu | Kohler 8/10/12RESVL specs

3.17 Date and Time Menu

The date and time will typically be set at controller power--up. To change the date, time, or time format (12 hour or 24 hour), use the Date and Time menu. See Figure 3-18.

3.18 Networking Information Menus

Use the networking menus to view and adjust communication settings for systems with remote RBUS devices such as a PIM or LCM or load shed kit, and for systems that use the Kohlerr OnCuer Plus Generator Management System.

RBUS is a proprietary RS-485 communications protocol.

The Networking Information menu leads to submenus for network and RBUS communication settings.

	Date and	Date:
	Time	Date:
	Time
		02Dec2011
		Time:
		12:34pm
		Time Format:
		12hr24hr
		<---- Return

tp6804

To change the date and time, press the Select button See Figure 3-7 for instructions.

			Figure 3-18Date and Time Menu
Networking---->	Networking---->		NS	See Figure 3-20.
	Status
Information
	Networking---->		NC	See Figure 3-21.
	Configuration

	RBUS	---->	RB	See Figure 3-22.
	Information

	<---- Return
				tp6810
Figure 3-19Networking Information Menu

TP-6880 10/14

Section 3 RDC2 Controller Operation 43

Image 43

Kohler 8/10/12RESVL manual Date and Time Menu, Networking Information Menus

Contents

TP-6880 10/14a RDC2 Controller Identification Accessory Number Accessory DescriptionProduct Identification Information Generator Set Identification Numbers Table of Contents Troubleshooting Scheduled MaintenanceDC2 Controller Operation Accidental starting Can cause severe injury or death Safety Precautions and InstructionsBattery Accidental Starting Fire Can cause severe injury or death Engine Backfire/Flash FireExhaust System Carbon monoxide Can Cause Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment List of Related Literature Transfer Switch LiteratureAccessory Literature Introduction Emission Compliance Period NameplateEmission Information Generator Set Application Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Load Control Module LCM AccessoriesCarburetor Heater Programmable Interface Module PIM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Exercise Automatic Operation with Other Transfer SwitchesSetting the Exerciser Unloaded Cycle Exercise with Complete System Diagnostics Loaded Full-Speed Exercise with RXT only Power Failure During Exercise CycleSystem Diagnostics Unloaded Full-Speed Exercise Shutdowns FaultsATS Communication Errors Resetting the Controller after a Fault Shutdown Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 Controls and Indicators RDC2 Generator Set/ Transfer Switch ControllerRDC2 Controller Operation LED Operation Controller Keypad LED IndicatorsButton Button Function Active Alert LCD Display Procedure to Change Settings Controller PowerBattery Charging Changing Settings 7Changing Settings Changing Settings on the RDC2 Controller Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Voltage Regulator VR Voltage Adj Setting the ExerciserAdjusting the Display Contrast Genset System Menu Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Password Networking Configuration Submenu OnCue Plus PasswordDhcp Submenu 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Description Controller KeypadButton Button Function LED Indication 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Low Oil Pressure Shutdown Oil Change ProcedureLubrication System Engine Oil Recommendation Fill with oil Reset the maintenance timer on the controllerDrain the oil Replace the oil filter Model Resvl DC2 Resetting the Maintenance TimerSpark Plugs Model Resv RDC2 Air Cleaner, 8RESV/RESVL Models Air Cleaner ServicePaper Element Service Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 USB Port TroubleshootingFault Messages Introduction Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14