Password, Dhcp Submenu | Kohler 8/10/12RESVL manual

3.18.2Networking Configuration Submenu (OnCue Plus Password)

The Networking Configuration menu includes settings used for communication with the Kohlerr OnCuer Plus Generator Management System.

Password

Note: Use the OnCue password shown on the controller display for OnCue Plus applications.

For the initial OnCue Plus setup, you will be required to reset the OnCue password on the RDC2 controller, and then enter it into the OnCue Plus software. To reset the password, follow the instructions in Figure 3-21.

Note: The password is displayed for only 10 seconds. Be sure to write down the password and serial number.

A new password is generated each time the reset password procedure is performed. If the password is

reset after the OnCue Plus system has been set up, the connection will be lost. Disconnect the battery power to the controller, wait a minute, then reconnect power.

DHCP Submenu

For most applications, the Dynamic Host Configuration Protocol (DHCP) is enabled and the IP settings cannot be changed from the controller keypad. If DHCP is enabled, IP parameters are not displayed.

If DHCP is disabled (i.e., if a static IP address is required), then the IP parameters can be modified. For applications that require static IP addresses, press and hold the select button to enable editing, disable DHCP, and then step to the next parameters and enter the information.

If an error occurs while setting a parameter, an error message is displayed and then the controller exits the edit mode. Previous settings are preserved.

TP-6880 10/14

Section 3 RDC2 Controller Operation 45

Image 45

Kohler 8/10/12RESVL manual Networking Configuration Submenu OnCue Plus Password, Dhcp Submenu

Contents

TP-6880 10/14a RDC2 Product Identification Information Accessory Number Accessory DescriptionGenerator Set Identification Numbers Controller Identification Table of Contents Scheduled Maintenance TroubleshootingDC2 Controller Operation Battery Safety Precautions and InstructionsAccidental Starting Accidental starting Can cause severe injury or death Exhaust System Engine Backfire/Flash FireCarbon monoxide Can Cause Fire Can cause severe injury or death Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment Accessory Literature Transfer Switch LiteratureIntroduction List of Related Literature Emission Information NameplateGenerator Set Application Emission Compliance Period Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Carburetor Heater AccessoriesProgrammable Interface Module PIM Load Control Module LCM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Setting the Exerciser Automatic Operation with Other Transfer SwitchesUnloaded Cycle Exercise with Complete System Diagnostics Exercise System Diagnostics Power Failure During Exercise CycleUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT only ATS Communication Errors FaultsResetting the Controller after a Fault Shutdown Shutdowns Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Generator Set/ Transfer Switch Controller Controls and IndicatorsRDC2 Controller Operation Button Controller Keypad LED IndicatorsButton Function LED Operation Active Alert LCD Display Battery Charging Controller PowerChanging Settings Procedure to Change Settings 7Changing Settings Changing Settings on the RDC2 Controller Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Adjusting the Display Contrast Setting the ExerciserGenset System Menu Voltage Regulator VR Voltage Adj Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Networking Configuration Submenu OnCue Plus Password PasswordDhcp Submenu 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Button Button Function Controller KeypadLED Indication Description 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Lubrication System Oil Change ProcedureEngine Oil Recommendation Low Oil Pressure Shutdown Drain the oil Reset the maintenance timer on the controllerReplace the oil filter Fill with oil Spark Plugs Resetting the Maintenance TimerModel Resv RDC2 Model Resvl DC2 Air Cleaner Service Air Cleaner, 8RESV/RESVL ModelsPaper Element Service Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Fault Messages TroubleshootingIntroduction USB Port Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14