ATS Status Menu | Kohler 8/10/12RESVL instruction

3.15 ATS Status Menu

ATS menus appear if a Model RXT transfer switch is connected to the generator set. If no transfer switch is connected, or another model ATS is connected to the engine start connections, Remote ATS is displayed on the ATS Status screen.

The ATS Status menu displays Model RXT transfer switch and source information.

The voltage shown in these menus can be calibrated. Follow the safety precautions at the beginning of this manuals. Use a voltmeter to measure the line-to-line voltage and follow the instructions in Figure 3-16 to calibrate the voltage readings.

ATS ---->

Status

	Note: If there is no Model RXT transfer
	switch connected to the generator set,
ATS Position:	Remote ATS is displayed and the other
Normal	screens on this page do not appear.

Normal Status:

Not/Acceptable

Emerg. Status:
Standby	Note: Sample data shown.
	Note: Sample data shown.

	Single-phase	Three-phase
	Normal Volts:	Normal Voltage:
	240.0 V	L1--L2	240 V
	Normal Freq.:	Normal Voltage:
	60.0 Hz	L2--L3	240 V
	Emerg Volts:	Normal Voltage:
	240.0 V	L3--L1:	240 V
	Emerg. Freq.:	Normal Freq.:
	60.0 Hz		60.0 Hz
		Normal Rotation:
			Similar screens appear for
			the emergency source.
	Reset	Reset
	Calibration	Calib? No
	<---- Return	Reset	tp6810
	<---- Return	Calib? Yes
		Calib? Yes

Figure 3-16ATS Status Menu, with Calibration

TP-6880 10/14

Section 3 RDC2 Controller Operation 41

Image 41

Kohler 8/10/12RESVL manual ATS Status Menu, Screens on this page do not appear

Contents

TP-6880 10/14a RDC2 Product Identification Information Accessory Number Accessory DescriptionGenerator Set Identification Numbers Controller Identification Table of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Battery Safety Precautions and InstructionsAccidental Starting Accidental starting Can cause severe injury or death Exhaust System Engine Backfire/Flash FireCarbon monoxide Can Cause Fire Can cause severe injury or death Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment Accessory Literature Transfer Switch LiteratureIntroduction List of Related Literature Emission Information NameplateGenerator Set Application Emission Compliance Period Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Carburetor Heater AccessoriesProgrammable Interface Module PIM Load Control Module LCM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Setting the Exerciser Automatic Operation with Other Transfer SwitchesUnloaded Cycle Exercise with Complete System Diagnostics Exercise System Diagnostics Power Failure During Exercise CycleUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT only ATS Communication Errors FaultsResetting the Controller after a Fault Shutdown Shutdowns Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators Button Controller Keypad LED IndicatorsButton Function LED Operation Active Alert LCD Display Battery Charging Controller PowerChanging Settings Procedure to Change Settings 7Changing Settings Changing Settings on the RDC2 Controller Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Adjusting the Display Contrast Setting the ExerciserGenset System Menu Voltage Regulator VR Voltage Adj Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Dhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Button Button Function Controller KeypadLED Indication Description 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Lubrication System Oil Change ProcedureEngine Oil Recommendation Low Oil Pressure Shutdown Drain the oil Reset the maintenance timer on the controllerReplace the oil filter Fill with oil Spark Plugs Resetting the Maintenance TimerModel Resv RDC2 Model Resvl DC2 Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Fault Messages TroubleshootingIntroduction USB Port Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14