Programmable Interface Module PIM Status Menu | Kohler 8/10/12RESVL

3.19Programmable Interface Module (PIM) Status Menu

The PIM status menu displays the status of inputs and outputs connected to the programmable interface module (PIM). this menu appears only if a PIM is connected. This is a status display menu only. Input and output settings cannot be changed from the RDC2 controller’s user interface.

Apersonal computer running Kohlerr SiteTecht software is required to change the input and output settings. Contact an authorized distributor or dealer for service.

The Kohlerr OnCuer Plus Management System can be used to turn outputs on and off. See the OnCuer Plus Software Operation Manual for instructions.

PIM	PIM 1	---->
Status:
	<---- Return

Input 1

In/Active

Input 2

In/Active

Output 1:

In/Active

Output 2:

In/Active

Output 3:

In/Active

Output 4:

In/Active

Output 5:

In/Active

Output 6:

In/Active

<---- Return

tp6810

Figure 3-24Programmable Interface Module (PIM) Status Menu

TP-6880 10/14

Section 3 RDC2 Controller Operation 49

Image 49

Kohler 8/10/12RESVL manual Programmable Interface Module PIM Status Menu

Contents

TP-6880 10/14a RDC2 Product Identification Information Accessory Number Accessory DescriptionGenerator Set Identification Numbers Controller Identification Table of Contents Troubleshooting Scheduled MaintenanceDC2 Controller Operation Battery Safety Precautions and InstructionsAccidental Starting Accidental starting Can cause severe injury or death Exhaust System Engine Backfire/Flash FireCarbon monoxide Can Cause Fire Can cause severe injury or death Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment Accessory Literature Transfer Switch LiteratureIntroduction List of Related Literature Emission Information NameplateGenerator Set Application Emission Compliance Period Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Carburetor Heater AccessoriesProgrammable Interface Module PIM Load Control Module LCM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Setting the Exerciser Automatic Operation with Other Transfer SwitchesUnloaded Cycle Exercise with Complete System Diagnostics Exercise System Diagnostics Power Failure During Exercise CycleUnloaded Full-Speed Exercise Loaded Full-Speed Exercise with RXT only ATS Communication Errors FaultsResetting the Controller after a Fault Shutdown Shutdowns Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 Controls and Indicators RDC2 Generator Set/ Transfer Switch ControllerRDC2 Controller Operation Button Controller Keypad LED IndicatorsButton Function LED Operation Active Alert LCD Display Battery Charging Controller PowerChanging Settings Procedure to Change Settings 7Changing Settings Changing Settings on the RDC2 Controller Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Adjusting the Display Contrast Setting the ExerciserGenset System Menu Voltage Regulator VR Voltage Adj Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Password Networking Configuration Submenu OnCue Plus PasswordDhcp Submenu 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Button Button Function Controller KeypadLED Indication Description 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Lubrication System Oil Change ProcedureEngine Oil Recommendation Low Oil Pressure Shutdown Drain the oil Reset the maintenance timer on the controllerReplace the oil filter Fill with oil Spark Plugs Resetting the Maintenance TimerModel Resv RDC2 Model Resvl DC2 Air Cleaner, 8RESV/RESVL Models Air Cleaner ServicePaper Element Service Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 Fault Messages TroubleshootingIntroduction USB Port Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14